Stopping distance and correct braking
Contents
Stopping a car does not begin when the wheels start to slow down.
First, the driver must:
- notice the hazard,
- recognise the situation,
- make a decision,
- apply the brake.
Only then does the vehicle's actual braking begin.
That is why the full distance needed to stop is best understood as:
reaction distance + braking distance = stopping distance.
This is one of the most important relationships in the whole theory of safe driving.
1. Reaction distance
Reaction distance is the distance the car travels from the moment a situation requiring a response arises until effective braking begins.
It is influenced primarily by:
- speed,
- the time the driver needs to notice and recognise the hazard,
- concentration,
- fatigue,
- distraction,
- alcohol and other substances,
- how predictable the situation is.
Important
During the reaction time, the car:
continues to travel at approximately the same speed.
2. One second at different speeds means a completely different distance
As a teaching example, assume a reaction lasting 1 second.
| Speed | Distance in 1 second |
|---|---|
| 30 km/h | approx. 8.3 m |
| 50 km/h | approx. 13.9 m |
| 70 km/h | approx. 19.4 m |
| 90 km/h | 25 m |
| 120 km/h | approx. 33.3 m |
| 140 km/h | approx. 38.9 m |
This is not a fixed human reaction time
One second has been used only to show the effect of speed.
In a real situation, the reaction may be:
- shorter,
- longer,
- multi-stage.
That is why you should not learn:
“a driver's reaction time is always 1 second”.
3. Braking distance
Braking distance is the distance from the start of effective braking until the vehicle stops.
It depends, among other things, on:
- initial speed,
- road-surface grip,
- tyre condition,
- the condition of the braking system,
- road gradient,
- weather conditions,
- braking technique,
- the vehicle's design and load.
There is no single universal braking-distance table that applies to every car and all conditions.
4. Stopping distance
The full stopping distance consists of:
REACTION DISTANCE
BRAKING DISTANCE
=
STOPPING DISTANCE
A logical example
You see an obstacle.
The car travels a dozen or several dozen metres before you begin braking.
It then needs further distance to lose speed.
That is why the obstacle may be:
too close for a safe stop even before the driver touches the brake pedal.
5. Speed affects stopping distance twice
Higher speed causes:
firstly
a greater distance to be travelled during the reaction time;
secondly
much greater energy that must be dissipated during braking.
That is why an increase in speed does not produce merely a proportional increase in the overall stopping distance.
6. Braking distance increases much faster than speed
In a simplified physical model, with the same grip and braking conditions:
braking distance increases approximately in proportion to the square of speed.
What does this mean?
If speed doubles:
→ the braking distance alone may be about four times longer.
If speed triples:
→ it may be about nine times longer.
This is a physical relationship, not a statutory table
The actual distance depends on many additional factors.
The most important conclusion:
an apparently small increase in speed can greatly increase the space needed to stop.
7. Why does this happen?
The kinetic energy of a moving vehicle depends on the square of its speed:
E = 1/2 × m × v²
During braking, the car's systems and the contact between the tyres and the road surface must dissipate this energy.
That is why a car travelling twice as fast does not merely have “twice the problem”.
It has much more energy to dissipate.
You do not need to memorise the formula for the exam.
You need to understand the relationship:
higher speed → disproportionately greater energy and braking distance.
8. Article 19 requires a speed that allows the driver to remain in control of the vehicle
The law does not allow a driver to excuse themselves by saying:
“I was driving within the speed limit, but I did not manage to brake in time”.
Article 19(1) requires driving at a speed that ensures control of the vehicle, taking into account, among other things:
- the condition and visibility of the road,
- the condition and load of the vehicle,
- weather conditions,
- traffic volume,
- the terrain.
The permitted speed is:
the maximum legal limit, not a guarantee that it is safe to travel at that speed in the given conditions.
9. A driver is also required to brake correctly
Article 19(2)(2) requires a driver to:
brake in a manner that does not cause a road-safety hazard or obstruct traffic.
In a normal situation, this means, among other things:
- observing traffic in advance,
- beginning to slow down early enough,
- avoiding unnecessarily abrupt braking.
However, it does not mean:
“you must never brake sharply”.
If sudden braking is necessary to avoid an accident:
→ safety requires an effective response.
10. Normal braking and emergency braking are two different situations
Normal braking
Used, for example, before:
- a red light,
- an intersection,
- a speed restriction,
- slower traffic.
It should be:
- early enough,
- smooth,
- predictable.
Emergency braking
Used when a sudden hazard appears:
- a pedestrian,
- a vehicle failing to give way,
- an obstacle,
- a sudden stop in traffic.
The goal is then one thing:
to reduce speed or stop the car as quickly as possible while retaining as much control as possible.
11. During emergency braking, time matters more than comfort
In a sudden-hazard situation, you should not:
- brake too gently for fear of a “jerk”,
- delay your reaction,
- first look for a better lane.
First:
→ reduce speed immediately.
If the situation requires an additional avoidance manoeuvre, perform it within the available:
- grip,
- space,
- vehicle controllability.
12. ABS — basic function
ABS is a system that prevents prolonged wheel lock during heavy braking.
It therefore helps retain:
the ability to steer the vehicle while braking.
Important
ABS:
- does not create additional grip,
- does not override the laws of physics,
- does not guarantee the shortest braking distance on every possible surface.
Its key advantage is limiting wheel lock and maintaining steering ability within the available grip.
13. A car with ABS — how should you brake in an emergency?
In a typical modern car equipped with ABS:
- press the brake pedal hard,
- maintain firm pressure,
- do not “pump” the brake,
- steer the vehicle if the situation requires it and there is available space.
While ABS is operating, the driver may feel:
- pedal pulsation,
- vibrations,
- a characteristic sound.
This may be a normal sign of the system operating.
Do not release the pedal just because it starts to pulse
In an emergency, maintain braking as required.
14. Why do we not “pump” the pedal in a car with ABS?
The system itself repeatedly regulates braking pressure at the wheels.
By manually:
- pressing,
- releasing,
- pressing again
the driver may only limit the system's ability to work effectively.
Therefore, during emergency braking with functioning ABS:
→ firm and continuous pressure on the brake.
15. A car without ABS behaves differently
In an older vehicle without ABS, excessive braking force can cause:
the wheels to lock.
With the front wheels locked, the ability to steer the vehicle is severely limited.
That is why braking technique in such a car requires a better feel for the grip limit.
For Category B training, the most important conclusion is:
know the design of the car you are driving and do not thoughtlessly transfer techniques appropriate to one system to another.
16. A locked wheel does not mean “maximum control”
When a wheel stops rolling and slides across the road surface:
- the ability to steer deteriorates,
- the direction of the car becomes harder to control.
ABS tries to keep the wheel within a range in which it is possible both to:
- brake heavily,
- retain the ability to change direction.
17. ABS does not allow you to ignore distance
A common mistake:
“I have ABS, so I can drive closer”.
No.
If the car ahead begins braking sharply:
- you still need reaction time,
- your tyres still have limited grip,
- the road surface still affects braking.
ABS does not reduce to zero:
reaction distance or braking distance.
18. ESP/ESC also does not replace the correct speed
The vehicle stability system may help when the car begins to:
- understeer,
- oversteer.
leave the expected path.
It may brake individual wheels and reduce drive torque.
However, this does not mean that the driver can:
- enter a bend too fast,
- swerve sharply around obstacles without consequences.
If there is not enough grip:
→ electronics cannot create it from nothing.
19. Tyres determine how effectively the brakes can be used
The brakes may be very effective, but braking force must be transmitted to the road through:
the tyres.
Braking distance is therefore influenced by:
- tread,
- rubber condition,
- pressure,
- temperature,
- tyre type,
- road surface.
A car with very good brakes and poor tyres may still have a serious problem stopping.
20. A wet road surface increases the margin required
Water between the tyre and the road surface can reduce grip.
That is why, when it is raining, you should:
- reduce speed,
- increase the distance,
- begin braking earlier.
The more water there is and the poorer the tyre condition:
→ the greater the risk of losing grip.
We will develop aquaplaning further in M6.3/M6.4.
21. Snow and ice can radically reduce braking effectiveness
On a slippery surface, the car needs much more space.
Do not use one simple table:
“on ice, always X times more”.
Actual grip depends on:
- the type of ice or snow,
- temperature,
- tyres,
- speed,
- whether the road has been gritted.
The conclusion is simple:
on a very slippery surface, slow down earlier and radically increase the distance.
22. A descent can increase stopping distance
On a descent, gravity acts in the direction of vehicle travel.
That is why, at the same speed and grip, stopping on a descent may require:
- a greater distance,
- beginning to slow down earlier.
On an ascent, the situation may be more favourable for braking, but this does not remove the need to maintain the correct distance.
23. Load and a trailer change how the combination behaves
Article 19 expressly requires taking into account:
the condition and load of the vehicle.
A car that is:
- heavily loaded,
- towing a trailer
may respond differently during:
- braking,
- a sudden change of path,
- braking on a bend.
Do not use the simplification
“a car twice as heavy always has exactly twice the braking distance”.
The actual relationship is more complex.
The practical conclusion:
→ a heavier load or a trailer requires a greater margin and earlier braking planning.
24. An incorrectly distributed load may reduce stability during braking
It is not only mass that matters.
What also matters is:
- weight distribution,
- centre-of-gravity height,
- securing of luggage,
- axle load.
During sudden braking, an unsecured load may:
- shift,
- change how the vehicle behaves,
- strike people in the passenger compartment.
The detailed rules for carrying loads will return in Module 11.
25. Braking on a bend is more demanding
A tyre has a limited ability to transmit forces.
On a bend, part of the available grip is already being used to:
change the direction of travel.
If you brake very hard at the same time:
→ the risk of losing stability or exceeding the available grip increases.
That is why safe technique usually involves:
reducing speed before the bend.
This does not mean that braking on a bend is prohibited in an emergency.
When an accident must be avoided:
→ brake as required and within the vehicle's capabilities.
26. Engine braking can help control speed
After easing off the accelerator and keeping an appropriate gear engaged, the engine provides resistance and helps limit speed.
Engine braking can be particularly useful:
- on a long descent,
- when slowing down is anticipated,
- to maintain speed without constantly using the service brake heavily.
However, it does not replace the brake when:
a quick stop is needed.
27. On a long descent, do not coast unnecessarily
Driving in gear allows you to use:
- engine braking,
- better control of speed.
Maintaining speed for a long time solely with the service brake on a steep descent may lead to:
- heating of the brakes,
- reduced braking effectiveness.
In a modern car, the way in which a gear ratio is selected may depend on whether the transmission is:
- manual,
- automatic,
- operating in a particular driving mode.
The driver should use the solutions provided by the vehicle manufacturer.
28. Do not brake with your left foot during ordinary passenger-car driving just to “be quicker”
In typical Category B training in a car with a clutch pedal:
- the right foot operates the accelerator and brake,
- the left foot operates the clutch.
In an automatic car, as standard:
→ the accelerator and brake are also operated with the right foot.
This reduces the risk of accidentally pressing both pedals at the same time and corresponds to standard learner-driving technique.
This is not a separate provision of Poland's Prawo o ruchu drogowym (the road traffic law), but a driving-technique rule.
29. The clutch during emergency braking in a manual car
In a car with a manual gearbox, during very heavy braking to a stop:
- effective braking is the priority,
- the clutch should be depressed at the appropriate point so that the engine does not stall as the vehicle stops and the vehicle can be operated correctly.
Do not begin the entire reaction by wondering:
“clutch first or brake first?”
First, respond to the hazard:
→ the brake is crucial.
30. Brake lights inform the driver behind you
When the service brake is used, the appropriate brake lights inform vehicles behind that you are braking.
That is why properly functioning brake lights are directly relevant to safety.
The driver behind must still maintain their own safe distance.
However, malfunctioning lights must not be ignored because they make it harder for others to recognise quickly that you are braking.
31. Emergency stop signal in a modern vehicle may operate automatically
Some cars have an emergency braking signalling system.
During very intensive braking, the vehicle may automatically:
- flash the brake lights rapidly,
- and, after stopping, activate the hazard warning lights under specified conditions.
This is a vehicle design system.
It does not change the driver's basic technique:
→ notice the hazard, brake effectively, control the vehicle's path.
32. Do not use the parking brake as the primary brake during normal driving
The parking brake is used primarily to:
immobilise the vehicle when parked.
The vehicle's technical system also provides a secondary braking function in accordance with construction requirements, but this does not mean that, during normal braking, the driver should replace the brake pedal with the parking brake.
Sudden use of a traditional parking brake while driving may:
- disturb stability,
- lock the wheels on an axle,
- cause a skid.
If the service brake actually fails, the procedure depends on the vehicle's design.
33. An electronic parking brake may have an emergency function — check the manual
In a car with an electronic parking brake, holding the switch while driving may activate:
- controlled emergency braking,
- using the vehicle's electronics.
How it operates varies between models.
Therefore:
→ do not experiment while driving.
Read the manual for the specific car.
34. If the brakes behave unusually, do not ignore the symptoms
Warning signs may include:
- a pedal travelling significantly deeper than usual,
- a very hard pedal,
- the car pulling to one side during braking,
- strong vibrations unrelated to normal ABS operation,
- metallic noises,
- a braking-system warning light,
- a clear reduction in effectiveness.
If a fault may endanger safety:
→ do not continue normal driving as if nothing had happened.
35. Braking for a predictable hazard should begin earlier
A good driver does not wait until the last moment before:
- a pedestrian crossing,
- a bend,
- a traffic jam,
- a motorway exit,
- traffic lights.
Easing off the accelerator earlier:
- gives more time,
- allows gentler braking,
- reduces the risk of being hit from behind,
- improves traffic flow.
Anticipation is part of correct braking.
36. Sudden braking by the vehicle ahead shows why distance is essential
M6.1 and M6.2 form one mechanism:
M6.1
distance gives you:
time and space.
M6.2
braking uses:
time and space to stop.
If there is not enough distance:
→ even a highly capable car may physically be unable to stop in time.
37. Do not assume that your car will brake in the same way as the vehicle ahead
Two cars may differ in:
- tyres,
- brakes,
- mass,
- load,
- assistance systems,
- technical condition.
The vehicle ahead may stop:
more effectively than yours.
This is another reason not to tailgate.
38. Do not test braking distance in normal traffic
Do not deliberately brake sharply on a public road just to:
“see how the car brakes”.
This may create a hazard for:
- passengers,
- vehicles behind,
- other road users.
Emergency-braking practice should take place:
- on a closed training area,
- in safe conditions,
- preferably under an instructor's supervision.
Step-by-step method for correct braking
Normal situation
Step 1 — look well ahead
Recognise the need to slow down earlier.
Step 2 — ease off the accelerator
If the situation allows.
Step 3 — begin smooth braking
Adjust the force to the distance and conditions.
Step 4 — keep observing
Check:
- the situation ahead,
- the mirror,
- how the situation may continue to change.
Step 5 — stop with a safe margin
Do not “rush” abruptly into the final metre.
Step-by-step method for emergency braking in a car with ABS
Step 1 — react immediately
Do not delay braking.
Step 2 — press the brake hard
Firm pressure.
Step 3 — maintain pressure
Do not pump the pedal.
Step 4 — steer if necessary and if there is a safe path
ABS helps retain steering ability.
Step 5 — look where you want to go
Do not focus your eyes solely on the obstacle.
Step 6 — secure the situation after stopping
If the hazard still exists.
Common pitfalls
1. Stopping distance consists of reaction distance and braking distance.
2. During reaction time, the car still travels a significant distance — at 90 km/h, about 25 m in the example 1 second.
3. One second is a teaching example, not a fixed statutory or biological reaction time for every driver.
4. Under the same conditions, braking distance increases approximately with the square of speed; twice the speed may mean about four times the braking distance alone.
5. The permitted speed is not a guarantee that you can stop before every obstacle.
6. Article 19 requires speed to be adapted, among other things, to the condition and visibility of the road, the weather, and the condition and load of the vehicle.
7. The provision requires braking without causing a hazard or obstruction, but it does not prohibit necessary hard braking in an emergency.
8. In a car with ABS, during emergency braking we typically press the brake hard and maintain pressure — we do not pump the pedal.
9. Pedal pulsation may be a normal sign of ABS operation.
10. ABS helps retain steering ability, but it does not create grip and does not guarantee the shortest distance in every condition.
11. Good brakes do not replace good tyres.
12. A wet, snow-covered or icy road requires a greater margin and earlier braking.
13. On a long descent, it is worth using an appropriate gear and engine braking rather than constantly placing a heavy load on the service brake.
14. The parking brake is not the primary method of normal braking while driving.
15. The greater the distance you maintain, the more of the stopping distance you actually have available.
Sources
- Rozporządzenie w sprawie szkolenia osób ubiegających się o uprawnienia do kierowania pojazdami:
- Annex No. 1,
officialTopic 2.5— “Vehicle distances and braking”.
- Annex No. 1,
- Ustawa z dnia 20 czerwca 1997 r. — Prawo o ruchu drogowym:
- Article 19(1) — duty to drive at a speed that ensures control of the vehicle, taking into account, among other things, the terrain, the condition and visibility of the road, the condition and load of the vehicle, the weather and traffic volume,
- Article 19(2)(2) — duty to brake in a manner that does not cause a road-safety hazard or obstruction,
- Article 19(2)(3) — duty to maintain the distance necessary to avoid a collision.
- Rozporządzenie Ministra Infrastruktury w sprawie warunków technicznych pojazdów oraz zakresu ich niezbędnego wyposażenia:
- chapter on braking systems — requirements for the service brake, secondary brake and parking brake, and their effectiveness.
- The relationship
braking distance ~ v²is a physical model assuming comparable grip and braking-system conditions. - The distance travelled in 1 second is calculated using the conversion
km/h ÷ 3.6 = m/s. - ABS: driving-technique layer — its primary purpose is to limit wheel lock and help retain steering ability during heavy braking.
- Current text of the road traffic law and technical requirements — state of the law in force in 2026.
