Category BM6.3
Lesson 3 of 7

Grip, road surface and the risk of skidding

Contents

A car can:

  • accelerate,
  • brake,
  • turn

only because the tyres are in contact with the road surface and can transmit the relevant forces.

In practice, we call this contact:

grip.

If grip is lower, the car has less ability to:

  • turn,
  • brake,
  • accelerate.

Therefore, the basic rule of this lesson is:

the worse the road surface and the lower the grip, the lower the speed, the greater the distance and the gentler the driver's inputs should be.


1. Grip is not a constant value

The same car may behave completely differently on:

  • dry asphalt,
  • wet asphalt,
  • block paving,
  • gravel,
  • mud,
  • snow,
  • ice.

Grip is also affected by:

  • tyre type,
  • tread condition,
  • pressure,
  • temperature,
  • speed,
  • load,
  • how the manoeuvre is performed.

That is why there is no single braking distance or one “safe speed” for every road surface.


2. Article 19 requires the road condition and weather to be taken into account

The law expressly requires the driver to travel at a speed that ensures control of the vehicle, taking into account, among other things:

  • the condition of the road,
  • road visibility,
  • the condition and load of the vehicle,
  • weather conditions,
  • the terrain,
  • traffic volume.

This means:

the formal speed limit is not automatically a safe speed.

If the road surface becomes slippery:

→ the driver should slow down accordingly even if sign B-33 has not changed.


3. A tyre has a limited “grip budget”

A tyre does not have an unlimited ability to transmit forces.

It must simultaneously handle:

longitudinal forces

  • acceleration,
  • braking,

and:

lateral forces

  • turning,
  • maintaining the path on a bend.

If you use a very large part of the available grip for turning:

→ less remains for hard braking or acceleration.

That is why braking at the limit while taking a sharp bend is more demanding than braking with the wheels straight.


4. The more slippery it is, the smaller the “budget”

On dry asphalt, a tyre can transmit relatively large forces.

On:

  • a wet surface,
  • snow,
  • ice,
  • loose gravel

the grip limit is much lower.

The same steering or braking input that is gentle on dry asphalt:

→ may cause a skid on ice.

That is why, on a low-grip surface, all driver inputs should be:

  • earlier,
  • gentler,
  • smoother.

5. A skid may occur during braking, acceleration or turning

There is no single type of skid.

A wheel may lose proper contact with the road surface during:

braking too hard

the wheel tends to lock;

accelerating too abruptly

a driven wheel may begin to rotate faster than would result from the vehicle's actual movement;

driving too fast on a bend

the tyres may be unable to maintain the required path.

Modern systems:

  • ABS,
  • ASR/TCS,
  • ESC/ESP

help limit these effects, but they do not increase the physical grip of the road surface.


6. ABS helps when braking, but it does not “stick” the car to the road

As we learned in M6.2, ABS limits prolonged wheel lock and helps retain steering ability during heavy braking.

However, if a tyre is on:

  • ice,
  • a very wet surface,
  • loose gravel,

the available grip is still low.

ABS can manage what is available.

It cannot create additional friction.


7. ASR/TCS limits wheelspin at the driven wheels

The traction-control system may respond when a driven wheel begins spinning excessively during acceleration.

It may, among other things:

  • reduce drive torque,
  • brake a selected wheel.

The driver may then notice:

  • a flashing warning light,
  • a temporary reduction in acceleration.

Conclusion

If the electronics intervene frequently during ordinary moving off:

→ this may mean that the driver is demanding more grip from the road surface than is available.


8. ESC/ESP helps stabilise the path, but it has limits

ESC can detect that the car is not moving in the direction expected by the driver.

The system may:

  • brake selected wheels,
  • reduce drive.

It helps counteract:

  • understeer,
  • oversteer.

However, it is not “electronic insurance” that allows you to enter a bend at any speed.

If speed is too high for the available grip:

→ even ESC may not prevent the vehicle from leaving its path.


9. Understeer — the car turns less than the driver expects

Understeer occurs when primarily the front tyres lose the ability to maintain the desired path.

The driver turns the steering wheel, but the car:

→ follows a wider arc than expected.

Typical mistake

The driver reacts:

“it isn't turning — so I'll turn the steering wheel even more”.

This may place an even greater demand on the front tyres.

Basic response

  • reduce the demands on the tyres,
  • smoothly ease off the accelerator,
  • do not make sudden movements,
  • if necessary, slightly reduce the steering angle so that the front wheels can regain grip,
  • look towards the safe path of travel.

The exact response to a skid is best practised at a closed training facility.


10. Oversteer — the rear of the car begins to “overtake” the front

Oversteer occurs when it is primarily the rear axle that loses grip.

The rear of the vehicle begins to move towards the outside of the bend.

The driver may feel that the car:

  • is rotating more than it should,
  • is beginning to turn sideways.

The response requires judgement

In a typical situation, you should:

  • look where you want to go,
  • avoid sudden braking and abrupt movements,
  • correct the steering direction in line with the movement of the skid,
  • avoid causing a sudden “snap” in the opposite direction.

How the vehicle behaves depends, among other things, on:

  • the drive system,
  • electronics,
  • speed,
  • the road surface.

That is why much more important than “recovering” a skid is:

driving at a speed that does not cause a loss of stability.


11. The safest way to deal with a skid is before it begins

A skid often results from a combination of:

  • excessive speed,
  • a sudden input,
  • a poor road surface.

The most effective method is therefore to:

  1. notice the poorer surface earlier,
  2. reduce speed before reaching it,
  3. drive through the difficult section smoothly.

Do not wait until the car begins to lose grip before slowing down.


12. Sudden inputs increase the risk of losing grip

On a slippery surface, avoid:

  • sudden steering,
  • abrupt acceleration,
  • hard braking unless necessary,
  • rapid lane changes.

Each such input suddenly increases the demand for grip.

Rule

the less grip — the more smoothly you must drive.


12A. Deliberately causing a skid is prohibited

In this lesson, we discuss a skid primarily as a hazard that the driver should prevent and respond to correctly.

From 30 March 2026, Article 60(5) of Poland's Prawo o ruchu drogowym (the road traffic law) additionally expressly prohibits driving a motor vehicle or moped in a manner:

  • deliberately causing the wheels to skid (drifting),
  • deliberately causing at least one wheel of the vehicle to lose contact with the road surface.

The Act provides a technical exception concerning wheels on lift axles in certain heavy vehicles of categories N2, N3 and M3. It has no practical relevance to a typical Category B passenger car.

Important distinction

  • an unintended skid on a slippery surface → a hazardous situation that must be brought under control,
  • deliberately putting the vehicle into a skid → conduct expressly prohibited by the road traffic law.

13. Sign A-15 “slippery road”

The sign:

A-15 “slippery road”

warns of the possibility of a vehicle skidding, caused in particular by:

  • a change in the road surface,
  • its permanent or periodic dampness.

This is very important wording.

A-15 does not only mean:

“there may be ice here in winter”.

It may relate to different causes of reduced grip.


14. A-15 does not automatically impose a specific speed limit

The warning sign:

A-15

does not mean:

“maximum 30 km/h”.

If a specific limit applies:

→ it results from B-33, a zone or other relevant provisions.

At the same time, Article 19 may require a speed significantly lower than the formal limit.

When you see A-15

  • reduce speed before the hazardous place,
  • increase the distance,
  • avoid sudden manoeuvres.

15. A change in the type of surface can change grip immediately

The boundary between the following may be hazardous:

  • asphalt → paving blocks,
  • new asphalt → old asphalt,
  • asphalt → concrete,
  • dry surface → wet surface,
  • carriageway → metal section.

For a moment, one axle of the car may be on a surface with different grip from the other.

This may be particularly important during:

  • braking,
  • turning.

Therefore, before a visible change in the surface:

→ it is worth reducing speed while still on the stable section.


16. Block paving may be much more slippery after rain

Paving blocks that are:

  • stone,
  • granite,
  • polished by traffic

may offer much less grip when wet than dry asphalt.

Take particular care:

  • on bends,
  • on steep streets,
  • while braking.

Do not assume that because the surface is hard:

→ it behaves in the same way as asphalt.


17. Drain covers and metal road elements

Manhole covers, metal bridge elements or trackwork may have different grip from asphalt.

When they are wet:

→ they may be noticeably more slippery.

In practice

If it can be done legally and safely:

  • do not brake sharply on them,
  • do not accelerate aggressively,
  • drive across them smoothly.

However, do not make a sudden swerve around a drain cover that creates a greater hazard than the surface itself.


18. Road markings may also have different grip

Lines, arrows and painted areas on the carriageway are made of materials that meet technical requirements, but their behaviour may differ from asphalt.

In particular:

  • when wet,
  • where the surface is worn

a rider of a two-wheeled vehicle may feel this difference very strongly.

A car should also avoid unnecessary sudden manoeuvres on a slippery section.


19. Leaves can form a layer with very little grip

Wet, crushed leaves can act between the tyre and the road surface like a slippery layer.

Particularly hazardous places include:

  • bends under trees,
  • shaded roads,
  • places where leaves accumulate at the edge.

In autumn, the road surface may look harmless and still offer reduced grip.


20. Mud and soil carried onto the road

Near:

  • fields,
  • construction sites,
  • exits used by heavy vehicles

the carriageway may become covered with:

  • soil,
  • mud,
  • clay.

After rain, such a layer may be very slippery.

The driver should

  • slow down sufficiently early,
  • avoid hard braking on the contaminated section,
  • maintain a smooth path.

21. Oil, fuel and other contamination

A patch of:

  • oil,
  • fuel,
  • fluid

may significantly reduce grip.

Not every dark patch on the carriageway must be oil, but if its origin is uncertain:

→ treat it as a potential hazard.

If you notice extensive hazardous contamination on the road:

→ you can notify the relevant services or the road authority.


22. Loose gravel reduces stability

On loose gravel, a tyre may move the stones rather than rest securely on a uniform surface.

This may result in:

  • easier skidding,
  • a weaker response to steering,
  • a longer braking distance.

In addition, stones may be thrown up by the wheels.


23. Sign A-28 “loose gravel”

A-28 warns of a section of road covered with:

  • gravel,
  • chippings,

which may be thrown up by the wheels of moving vehicles.

Correct response

  • reduce speed,
  • increase the distance from the vehicle ahead,
  • avoid abrupt acceleration,
  • avoid sudden steering movements.

A greater distance also reduces the risk of being struck by stones thrown up by the vehicle ahead.


24. A road surface under repair may change grip over a short section

At roadworks, you may encounter:

  • milled asphalt,
  • chippings,
  • differences in level,
  • temporary patches,
  • dust,
  • mud.

Sign A-14 provides information about roadworks, but the driver should additionally observe the actual condition of the carriageway.

Do not assume:

“if there is no A-15, the surface definitely has normal grip”.


25. Sign A-11 “uneven road”

A-11 warns of:

a transverse unevenness in the carriageway.

Unevenness is not the same as slipperiness.

However, it may cause:

  • temporary unloading of a wheel,
  • poorer contact between the tyre and the road surface,
  • a change of path,
  • an impact to the suspension.

Therefore, speed should be appropriately reduced before the uneven section.


26. Sign A-11a “speed hump”

A-11a warns of a raised part of the carriageway used to:

slow vehicle traffic.

Do not try to drive over the hump at the formal speed limit if:

  • the design of the hump,
  • the vehicle,
  • the situation

require a lower speed.

It is best to complete most of the braking before the hump, rather than braking very hard on the hump itself.


Supplementary plates discussed in this section:

27. Ruts change the vehicle's behaviour

Ruts can:

  • guide the wheels along their own path,
  • make changing lanes more difficult,
  • collect water,
  • increase the risk of aquaplaning.

The plate:

T-13

under A-30 indicates a section of road where there are surface deformations in the form of:

ruts.

Practical response

  • slow down,
  • hold the steering wheel steadily,
  • avoid suddenly “jumping” out of the rut.

28. A longitudinal step in the road surface can affect the path of the wheels

The plate:

T-12

under A-30 indicates:

a longitudinal step in the road surface.

It is particularly hazardous for:

  • motorcyclists,
  • cyclists,

but it can also affect a car when its path changes.

Cross the difference in level:

  • calmly,
  • under control,
  • without a sudden steering correction.

29. T-15 warns of a site of frequent accidents caused by a slippery road surface in rain

The plate:

T-15

under A-30 indicates a site of frequent accidents caused by:

a slippery road surface due to rainfall.

This is a signal that local conditions may be particularly treacherous.

Do not wait until you feel the vehicle skid.

→ slow down before this section.


30. The first minutes of rain can be particularly treacherous

A dry carriageway may contain:

  • dust,
  • rubber particles,
  • oily contamination.

After rain begins, these may for a time form a more slippery mixture.

This is not a universal rule that allows a specific time to be calculated.

The practical conclusion:

when it starts raining, immediately increase your safety margin.

We will discuss rain more broadly in M6.4.


31. Aquaplaning — the tyre loses direct contact with the road surface because of a layer of water

With the right combination of:

  • speed,
  • amount of water,
  • tyre condition,
  • pressure,
  • ruts

the tyre may be unable to disperse the water quickly enough.

A layer forms that separates the tyre from the road surface.

This is:

aquaplaning.

The car may then temporarily respond very poorly to:

  • steering,
  • braking,
  • acceleration.

32. There is no single statutory speed at which aquaplaning always begins

The risk depends on:

  • water depth,
  • speed,
  • tread,
  • pressure,
  • tyre design,
  • ruts.

That is why the following statement is incorrect:

“aquaplaning always starts at X km/h”

The faster you travel through deep water:

→ the greater the risk.


33. If aquaplaning occurs — avoid sudden inputs

If you feel that the car is beginning to “float” on the water:

  • hold the steering wheel steadily,
  • look towards the safe path,
  • smoothly reduce accelerator pressure,
  • do not make a sudden steering input,
  • avoid suddenly demanding a large braking force unless it is necessary to avoid an immediate hazard.

The aim is to allow the tyres to:

→ regain stable contact with the carriageway.

In an emergency, safety takes priority and the driver uses the vehicle's available systems as the situation requires.


34. The best defence against aquaplaning is choosing the speed before the puddle

If you see ahead of you:

  • a large amount of water,
  • deep ruts,
  • a large puddle,

do not wait until the car drives into it.

→ reduce speed before the water.

Hard braking once the tyre has already lost contact with the carriageway has limited effectiveness.


35. Tyres are crucial to grip

As discussed in M4.7, the regulations require tyres to be in an appropriate condition.

In practical terms, what matters is:

  • tread depth,
  • damage,
  • correct pressure,
  • tyre compatibility.

The tread helps, among other things, to:

→ disperse water from beneath the tyre.

A worn tyre may still be formally permitted but have a smaller safety margin in difficult conditions.


36. Pressure that is too low or otherwise incorrect also changes tyre behaviour

Pressure affects:

  • the shape of the contact patch,
  • heating,
  • stability,
  • wear.

Do not set the value “by eye”.

Use the values specified by the manufacturer for:

  • the tyre size,
  • the vehicle load.

TPMS helps detect problems, but it does not replace checking the tyre's condition.


37. Reduce speed before a bend, before steering sharply

The most stable sequence is:

  1. assess the bend,
  2. slow down appropriately on the straight section,
  3. begin turning smoothly,
  4. maintain a stable path,
  5. gradually increase drive after leaving the bend.

This does not mean:

“you must never brake on a bend”.

Braking may be necessary in an emergency.

The point is ordinary technique that limits the risk of using the entire “grip budget” at once.


38. Do not make a sudden manoeuvre to avoid a small pothole

A sudden steering jerk at high speed may create a greater risk than the:

  • pothole,
  • puddle,
  • drain cover.

If you notice the obstacle too late:

→ first assess whether changing your path is safe.

Do not move:

  • into the adjacent lane,
  • into the opposing lane,
  • into the path of another vehicle

just to protect a tyre or the suspension.


39. Different grip beneath the left and right wheels is particularly difficult

A possible situation is:

  • the left wheels are on dry asphalt,
  • the right wheels are on ice or a wet verge.

During braking, the forces on the two sides of the car are then different.

Modern ABS/ESC can help maintain direction.

However, the driver should:

  • hold the steering wheel steadily,
  • avoid sudden corrections,
  • reduce speed sufficiently early if such a change in the road surface is visible.

40. One wheel running onto a soft verge

If a wheel runs onto:

  • soil,
  • gravel,
  • a soft verge,

do not try to suddenly “pull” the car back onto the asphalt.

This may cause:

  • a sudden change of direction,
  • crossing the opposing lane,
  • loss of stability.

Safer response

  • maintain a smooth path,
  • reduce speed,
  • make sure the road is clear,
  • return to the carriageway with a smooth movement.

41. If the wheels begin to slide — look where you want to go

A driver has a natural tendency to look:

at the obstacle.

This can make correct steering more difficult.

When stability is lost:

→ look towards the safe place to which you want to guide the car.

This does not guarantee that control will be regained, but it helps you make movements consistent with the intended path.


42. Skid training should take place outside normal traffic

Theory allows you to understand:

  • understeer,
  • oversteer,
  • the operation of ABS and ESC.

The actual reactions of the car are best learned:

  • on a skid pad,
  • on a closed track,
  • under an instructor's supervision.

Do not try to deliberately cause a skid on a public road.


Step-by-step method on a section with reduced grip

Step 1 — notice the signals

  • A-15,
  • A-28,
  • A-11,
  • T-12 / T-13 / T-15,
  • mud,
  • water,
  • gravel,
  • leaves,
  • a change in the road surface.

Step 2 — slow down before the section

Not only once the vehicle starts to skid.

Step 3 — increase the distance

Especially on a wet or loose surface.

Step 4 — make smooth inputs

  • accelerator,
  • brake,
  • steering wheel.

Step 5 — avoid combining maximum manoeuvres

Do not try at the same time to:

  • steer very sharply,
  • brake very hard.

Step 6 — if the car loses stability

  • look in a safe direction,
  • reduce sudden inputs,
  • allow the safety systems to work,
  • correct smoothly.

Common pitfalls

1. Grip depends on the road surface, tyres, weather, speed and how the manoeuvre is performed — it is not a constant property of the road.

2. The formal speed limit does not guarantee safe driving on a slippery surface; Article 19 requires speed to be adapted to the road condition and weather conditions.

3. A tyre has a limited “grip budget” shared between turning, braking and acceleration.

4. ABS, ASR/TCS and ESC/ESP help manage the available grip, but they do not increase it.

5. Understeer means the car tends to turn less than expected; adding more and more steering angle may make the situation worse.

6. Oversteer means a loss of stability at the rear axle and the car rotating more than expected.

7. A-15 “slippery road” warns, among other things, of the possibility of skidding due to a change in the road surface or its dampness; it does not automatically impose a 30 km/h limit.

8. A-28 means loose gravel — slow down, increase the distance and watch out for stones thrown up by the wheels.

9. A-11 warns of transverse unevenness, while A-11a warns of a speed hump.

10. T-12 indicates a longitudinal step in the road surface, T-13 ruts, and T-15 a site of frequent accidents caused by a slippery road surface in rain.

11. When wet, paving blocks, metal elements, drain covers and some painted surfaces may have different grip from asphalt.

12. Aquaplaning does not begin at one universal speed — it depends, among other things, on water, speed, tread and pressure.

13. During aquaplaning, avoid sudden steering and accelerator inputs; the key measure is reducing speed earlier, before the water.

14. A sudden return from a soft verge to asphalt may cause loss of stability — the return should be controlled and smooth.

15. The most effective way to deal with a skid is to prevent it by choosing an appropriate speed and making smooth manoeuvres.

Sources
  • Ustawa z dnia 4 grudnia 2025 r. o zmianie niektórych ustaw w celu poprawy bezpieczeństwa ruchu drogowego — Dz.U. 2025 poz. 1872; Article 60(5) of the road traffic law in force from 30 March 2026 (ban on deliberate skidding and deliberately causing a wheel to lose contact with the road surface).

  • Rozporządzenie w sprawie szkolenia osób ubiegających się o uprawnienia do kierowania pojazdami:

    • Annex No. 1, officialTopic 2.6 — risk factors associated with road conditions and changes in those conditions.
  • Ustawa z dnia 20 czerwca 1997 r. — Prawo o ruchu drogowym:

    • Article 19(1) — duty to drive at a speed that ensures control of the vehicle, taking into account, among other things, the condition and visibility of the road, the condition and load of the vehicle, weather conditions and terrain,
    • Article 19(2) — correct braking and safe distance,
    • Article 66 — general requirements for the technical condition and equipment of a vehicle so that its use does not endanger safety.
  • Rozporządzenie w sprawie znaków i sygnałów drogowych:

    • § 7(1) — A-11 “uneven road”,
    • § 7(2) — A-11a “speed hump”,
    • § 7(6) — A-15 “slippery road”,
    • § 10(10) — A-28 “loose gravel”,
    • § 11 — A-30 and supplementary plates:
      • T-12 — longitudinal step in the road surface,
      • T-13 — ruts,
      • T-15 — site of frequent accidents caused by a slippery road surface in rain.
  • Physics of driving:

    • tyre grip is limited and is shared between transmitting longitudinal and lateral forces,
    • ABS/ASR/ESC manage the available grip but do not physically increase it,
    • the risk of aquaplaning depends, among other things, on speed, the amount of water, tread, pressure and road-surface conditions.
  • Current text of the road traffic law and the regulation on road signs and signals — state of the law in force in 2026.

  • In M6.4, we discuss in detail the effects of rain, snow, ice and strong wind; in M6.3, weather is covered only to the extent necessary to explain the mechanism of grip.

↑