Gear changing, clutch control and engine braking
Contents
In a car with a manual gearbox, the driver does not only choose the direction of travel and the speed.
They must also choose a gear that allows the car to:
- respond smoothly to the accelerator pedal,
- run at neither too high nor too low engine speed,
- have adequate acceleration available,
- slow down in a controlled way,
- avoid unnecessary “slipping” of the clutch,
- remain under full control when driving conditions change.
This is why changing gear is not something done mechanically according to a single speed table.
The driver should understand why they are changing gear and what the effect of the change will be.
In this lesson we focus mainly on a Category B passenger car with a manual gearbox.
We will discuss automatic, hybrid and electric cars by comparison where the way they are operated differs significantly.
1. What exactly follows from the official training programme?
In the theoretical part of the official training programme, topic 2.9 has the general name:
“Vehicle control techniques”.
The detailed practical training programme develops this area and lists, among other things:
- gear changing appropriate for energy-efficient driving,
- using engine torque while braking — engine braking.
Both skills are therefore an official part of driver preparation.
However, this does not mean that Poland's Prawo o ruchu drogowym (the road traffic law) specifies one mandatory gear for each speed or one technique for releasing the clutch.
You need to separate:
- the requirements of the training programme,
- specific test criteria,
- the general obligations of safe driving arising from the legal rules,
- technique adapted to the particular car.
2. The exam has a specific gear-changing criterion
The current examination regulations provide the following task for Category B:
“Gear changing appropriate for energy-efficient driving”.
For Categories B and B+E, the candidate should change up when the engine reaches:
from 1800 to 2600 rpm.
At the same time:
the first four gears should be engaged before the vehicle reaches 50 km/h.
This is a very specific test standard.
What does not follow from it?
It does not follow that:
- on every road you must always change gear at exactly the same engine speed,
- every car has identical engine and gearbox characteristics,
- 50 km/h is a “fourth-gear speed” laid down by the road traffic law,
- outside the exam there is a statutory requirement to drive in a specific gear at a specific speed.
The range of 1800–2600 rpm and the requirement concerning the first four gears are a test criterion laid down in the examination regulations.
It is not a general rule of the road traffic law assigning gears to speeds.
We will develop the wider topic of energy-efficient driving — anticipating situations, maintaining smoothness and avoiding unnecessary acceleration — in
M7.6.
3. Why does a car need gears?
A combustion engine can work efficiently only within a certain range of engine speed.
The car's wheels, by contrast, have to turn very slowly when moving off and much faster when driving at higher speed.
The gearbox makes it possible to match these two elements.
Put simply:
Lower gear
It gives greater use of tractive force at a lower vehicle speed.
It is needed, among other things:
- when moving off,
- at low speed,
- during stronger acceleration,
- on a steep ascent,
- when the car needs more tractive force again after slowing down.
Higher gear
At the same vehicle speed, it usually allows lower engine speed to be maintained.
It is appropriate when the car is already travelling fast enough and the engine can run smoothly under the current load.
lower gear → more force at lower speed
higher gear → calmer running at higher speed
This describes how the drivetrain works, not a table of required speeds.
4. One gear does not correspond to one fixed speed
Popular simplifications such as:
“second gear is up to 20 km/h, third up to 40 km/h”
may help a novice driver during their first drives, but they are not a universal standard.
The same gear may be appropriate at different speeds depending on:
- the design of the gearbox,
- the type of engine,
- its torque,
- the gradient of the road,
- the load in the car,
- the need to accelerate,
- traffic conditions.
The driver should learn to combine information from:
- the speedometer,
- the rev counter,
- the engine's response,
- the situation ahead of the vehicle.
5. What does the clutch do?
In a car with a manual gearbox, the clutch makes it possible to temporarily disengage the drive between the engine and the gearbox.
This allows the driver, among other things, to:
- move off,
- change gear,
- stop the car without the engine labouring,
- smoothly reconnect the engine to the drivetrain.
However, the clutch pedal is not used to regulate speed continuously during normal driving.
After a gear change, the clutch should be properly engaged again, and the left foot should not press the pedal without need.
This is a principle of correct technique and vehicle maintenance, not a separate rule of the road traffic law.
6. The basic sequence for changing up
In a typical car with a manual gearbox, changing up looks like this:
- you accelerate until the right moment to change gear,
- you lift off the accelerator,
- you press the clutch,
- you select the higher gear,
- you release the clutch smoothly,
- you use the accelerator pedal again as appropriate.
The movement should be smooth and coordinated.
Releasing the clutch too abruptly
This may cause:
- a jerk,
- a sudden change in the load on the drivetrain,
- reduced comfort and control of the car.
Holding partial clutch engagement for too long
This causes unnecessary clutch slip and wear.
After a gear change, the aim is to achieve full engagement of the drive as smoothly as possible.
7. Do not look at the gear lever while driving
Over time, changing gear should become something you do without taking your eyes off the road.
The driver should know the gear layout of the car they are driving.
Looking at the gear lever while driving means losing part of the information about:
- your path,
- the vehicle in front,
- pedestrians,
- signs and signals,
- emerging hazards.
At 50 km/h, a car covers about 14 metres in one second.
This is why even a brief loss of observation of the road matters.
8. After changing gear, your hand goes back to the steering wheel
You operate the gear lever when you are actually changing gear.
After completing the action, your hand should return to the steering wheel.
Constantly resting your hand on the gear lever:
- does not improve control of the car,
- reduces your ability to use both hands on the steering wheel quickly,
- in some designs may also put unnecessary load on the gear-selection mechanism.
This is good driving-technique practice.
9. Press the clutch when it is needed
A novice driver may tend to press the clutch “just in case”.
This is not a correct habit.
Holding the clutch pressed for a long time while rolling:
- disconnects the engine from the wheels,
- removes the possibility of using conventional engine braking,
- changes the way the car responds to the accelerator pedal.
The clutch is a tool for:
- moving off,
- changing gear,
- disengaging the drive appropriately before stopping or in other situations that require it.
It is not a “second brake”.
10. Do not keep your left foot on the clutch pedal
After completing a gear change, take your left foot off the clutch pedal and rest it in the place provided for it, if the vehicle's design allows.
Even slight constant pressure on the pedal may partially load the clutch mechanism.
In addition, with such a habit the driver may unknowingly disengage the drive in a situation where they need full control of the car.
This is a technical and maintenance tip.
11. When should you change up?
In normal driving, the decision depends on several things at once:
- engine speed,
- vehicle speed,
- the current load,
- the gradient of the road,
- whether you intend to keep accelerating,
- the characteristics of the particular engine.
In the Category B exam, there is also a specific criterion:
1800–2600 rpm when changing up.
In everyday use of the vehicle, however, the right moment may also depend on the manufacturer's recommendations and driving conditions.
Example
The car is travelling on a level road at a constant speed and the engine is running freely.
You can usually select a higher gear earlier than during:
- noticeable acceleration,
- driving up a steep ascent,
- driving with a heavy load.
Do not change gear only because you “always do it at the same speed”.
12. The first four gears before 50 km/h — how should the test criterion be understood?
The examination regulations state that for Categories B and B+E:
the first four gears should be engaged before the vehicle reaches 50 km/h.
The aim is to check whether the candidate can use the gearbox efficiently and does not keep the engine at high revs in a low gear without need.
Do not turn this into a false rule:
“in fourth gear you must always drive at 50 km/h”.
That is not what the provision says.
The criterion describes the point before which the first four gears should have been used while accelerating in the exam.
13. A gear that is too low at high speed
If the driver stays in a low gear for too long, the engine may run at unnecessarily high revs.
The result may be:
- more noise,
- higher fuel consumption,
- less smooth driving,
- unnecessary load on the drivetrain.
In extreme cases, wrongly changing down into a gear that is too low at high speed may cause a sudden rise in engine speed and make the vehicle jerk.
This is why, before changing down, you must make sure that the selected gear is appropriate for the current speed.
14. A gear that is too high at too low a speed
The opposite situation is also unfavourable.
If the car is moving slowly in too high a gear and the driver presses the accelerator pedal hard, the engine may:
- run unevenly,
- vibrate,
- respond poorly,
- have too little acceleration in reserve.
This is commonly called “labouring” the engine.
If you need noticeably more tractive force, the right reaction may be to change down, rather than pressing the accelerator pedal harder and harder in too high a gear.
15. Changing down — why do we do it?
Changing down means selecting a lower gear.
It may be needed when:
- the vehicle's speed has dropped noticeably,
- you intend to accelerate again,
- you are starting up an ascent,
- you need a greater reserve of tractive force,
- you want to use stronger engine braking.
What matters most is matching the gear to the vehicle's speed and the situation.
Do not change down automatically just because you see a lower number on the speedometer.
16. The basic sequence for changing down
In a typical situation:
- you assess how much the vehicle needs to slow down,
- you reduce speed accordingly,
- you press the clutch,
- you select a lower gear matched to the new speed,
- you release the clutch smoothly,
- you continue driving or use the resistance of the drive to slow down further.
The most common mistake of a novice driver is to select a gear that is too low and then release the clutch too abruptly.
This may cause:
- a strong jerk,
- a sudden increase in engine speed,
- reduced vehicle stability, especially on a slippery surface.
17. You do not have to go through every gear in turn each time you slow down
The examination regulations require correct gear changing and the use of engine braking, but they do not establish a rule that whenever the driver slows down they must go through the gears in turn:
5 → 4 → 3 → 2 → 1.
If, after slowing down, the speed corresponds to a different gear, you can select the gear appropriate to the current situation and the vehicle's design.
What matters most is that you:
- do not select a gear that is too low for the speed,
- do not stay in too high a gear at low speed,
- change gear smoothly,
- keep full control of the car.
During the exam, you must also remember the specific criterion concerning changing up during energy-efficient driving.
18. What is engine braking?
When the driver lifts off the accelerator and the car remains in gear with the clutch engaged, the drivetrain resists the vehicle's movement.
The car starts to slow down without the service brake having to be used continuously.
This is called engine braking.
The official programme describes this skill as:
“using engine torque while braking — engine braking”.
The current examination regulations also provide for this skill to be assessed for Category B.
19. Engine braking does not replace the service brake
Engine braking is part of speed control, but it is not suitable for every situation.
If you need to:
- lose speed quickly,
- stop at a specific place,
- react to a sudden hazard,
the basic tool is the service brake.
Engine braking can supplement it.
Do not delay using the brake just to “brake with the engine alone at all costs”.
Safety is more important than demonstrating technique.
20. How can you use engine braking when slowing down normally?
An example situation:
You are driving and you can see a red light in the distance.
Instead of keeping your foot on the accelerator until the last moment, you can:
- lift off the accelerator earlier,
- leave the car in gear,
- let the vehicle start to slow down partly because of the resistance of the drivetrain,
- use the service brake as much as needed to reduce speed further,
- select a lower gear if you intend to continue at a lower speed,
- before stopping completely, press the clutch early enough so that the engine does not labour.
This combines:
- anticipation,
- smoothness,
- correct gear changing,
- engine braking.
21. Pressing the clutch straight away removes conventional engine braking
If, when slowing down in a manual car, you press the clutch straight away and roll for a long time with the drive disengaged, the engine stops slowing the wheels through the gearbox.
This is why, during normal, anticipated slowing down, there is no need to press the clutch at the very first moment just because you intend to stop later.
Typically:
lift off the accelerator → braking / slowing down in gear → clutch only at the right moment
When to use the clutch depends on:
- the current gear,
- the speed,
- the vehicle's design,
- whether you are stopping completely or intend to continue.
This is driving technique, not a statutory number of seconds or metres.
22. Changing down can increase engine braking
The lower the appropriately chosen gear, the more noticeable the engine-braking effect may be.
This is why changing down can be used:
- during prolonged slowing down,
- when driving down a descent,
- when preparing to drive at a lower speed.
However, changing down must be matched to the speed.
Wrongly selecting a gear that is too low and releasing the clutch abruptly may make control worse instead of better.
23. On a long descent, select a gear that helps you control your speed
On a long descent, the car is accelerated by gravity.
If the driver constantly holds the speed using only the service brake, the braking system may heat up.
This is why good driving technique involves using:
- an appropriate gear,
- engine braking,
- the service brake to the extent needed.
Do not select too high a gear just so that the engine runs at very low revs.
On a descent, you also need speed control.
We covered the effect of a downhill gradient on braking and grip in Module 6.
24. “Coasting in neutral” is not a good substitute for choosing the right gear
In a manual car, once neutral is selected, the engine is no longer mechanically connected to the wheels through the gearbox.
In this situation you do not use conventional engine braking.
This is why, during anticipated slowing down or when driving down a descent, good technique is to stay in an appropriate gear instead of coasting in neutral without need.
In this lesson, we do not present coasting in neutral as such as a separate statutory prohibition that always applies.
What matters, however, is that:
- the training programme requires engine braking to be taught,
- the practical exam checks the use of engine braking,
- the driver is obliged to keep control of the vehicle and to brake safely.
25. Before a bend, prepare your speed first, then your gear
When approaching a bend, the safest approach is to do most of the necessary braking before the bend, while the vehicle is still travelling on a straighter path.
Then select the gear appropriate for the speed at which you will take the bend and possibly accelerate out of it.
Avoid unnecessary abrupt changes of:
- gear,
- clutch,
- accelerator,
- braking
at a moment when the tyres are already using part of their grip for cornering.
This is good driving-technique practice based on the principles of vehicle dynamics, not a separate legal rule requiring a gear change at a specific point in the bend.
26. On a slippery surface, change down particularly smoothly
Engaging the drive abruptly after changing down may cause a sudden change in the force acting on the driven wheels.
On a slippery surface, this may reduce the car's stability.
This is why on:
- snow,
- ice,
- slush,
- a very wet surface
all actions on the drivetrain should be particularly smooth.
It is not only about the accelerator pedal.
Releasing the clutch too abruptly after changing down may also upset the grip.
27. During emergency braking, effective braking takes priority over changing down
If a sudden hazard appears and you must stop the car as quickly as possible, the priority is effective use of the brake.
Do not try at such a moment to carry out a full sequence of calm downchanges through each gear.
In a manual car, use the clutch in such a way that you:
- do not interfere with braking as effectively as possible,
- do not allow the engine to stall as the car stops.
Emergency braking together with ABS was covered in detail in M6.2.
Here, the most important principle is:
emergency stop → brake effectively first; changing gear is not the priority.
28. Do not select reverse gear while moving forwards
Reverse gear is used for driving backwards.
Before selecting it, the car should be properly stopped in accordance with the vehicle's design and the manufacturer's recommendations.
Trying to engage reverse gear while moving forwards may:
- be blocked by the design of the gearbox,
- cause the mechanism to malfunction,
- lead to damage or loss of control.
This principle is of a technical and maintenance nature.
The detailed rules on the reversing manoeuvre itself were covered in Module 3.
29. What should you do after accidentally selecting the wrong gear?
If, after changing gear, you feel that the car:
- jerks sharply,
- the engine revs very high,
- the engine starts to labour,
- the vehicle does not respond as you expected,
do not try to “rescue” the situation by pressing the accelerator pedal harder and harder.
First:
- keep control of the direction of travel,
- use the clutch if this is needed to disengage the wrongly selected gear,
- select the correct gear,
- engage the drive smoothly again.
If the traffic situation requires a stop — stop the car safely and only then sort out the gearbox.
30. An automatic changes gear for the driver — but the driver is still responsible for the way they drive
In a car with an automatic gearbox, the driver usually does not use a clutch pedal and does not make every gear change manually.
The gearbox selects the gear depending, among other things, on:
- speed,
- load,
- accelerator pedal position,
- the selected driving mode.
The driver, however, still decides:
- how hard to accelerate,
- when to slow down,
- what speed to maintain,
- whether to select
D,R,Por another mode provided by the manufacturer, - whether to use the option of manually limiting or selecting the gear, if the vehicle offers it.
Do not carry over the rules for operating a manual clutch to an automatic car.
31. Sport mode, manual mode or a low gear range in an automatic
Some automatic gearboxes allow the driver to influence gear selection by means of:
- paddles on the steering wheel,
Mmode,- a position limiting the highest gear,
- modes intended for descents or for driving in particular conditions.
These solutions differ between models.
On a long descent, they can be used to increase the drivetrain braking effect instead of constantly loading the service brake.
Always use them in accordance with the instructions for the particular vehicle.
There is no single universal combination of gearbox markings for all cars.
32. Hybrid and electric cars may slow down differently
In a hybrid or electric car, regenerative braking may occur after the accelerator pedal is released.
The electric motor then acts as a generator, and some of the energy of motion can be recovered to the battery.
To the driver, the effect may resemble strong engine braking.
Depending on the car:
- the strength of regenerative braking may be fixed,
- it may be adjustable,
- it may depend on the selected mode,
- the vehicle may offer one-pedal driving.
This does not change the driver's basic responsibility:
you must control your speed and be ready to use the service brake when the situation requires it.
33. Do not learn the “sound of the gear” instead of observing the car
An experienced driver often recognises from the sound and response of the engine that a gear change is needed.
This is helpful information, but it should not be the only source.
In modern vehicles:
- engines are better soundproofed,
- turbocharging changes the torque characteristics,
- the vehicle may have a gear-change indicator,
- a hybrid drivetrain may behave very differently from a conventional manual car.
This is why you should assess together:
- engine speed,
- vehicle speed,
- load,
- the car's response,
- the situation on the road.
34. The gear-change indicator is an aid, not an overriding command
Many cars show the driver a symbol suggesting:
- changing up,
- changing down.
The system can help with economical driving, but it does not know the whole context as the driver does.
For example, any moment now there may be:
- a steep ascent,
- the need to join traffic briskly,
- overtaking,
- a bend requiring a reduction in speed.
The driver remains responsible for choosing the gear appropriate to the situation.
35. Changing gear must not distract you from the traffic
If the situation is complex — e.g. you are approaching a pedestrian crossing or an intersection, or the vehicle in front of you slows down sharply — you deal with the safety problem first.
There is no point in focusing all your attention on hitting a specific engine speed exactly if, at the same time, you stop observing the road.
Technique should serve safety, not replace it.
In the exam, too, correct gear changing is assessed in real traffic, and therefore together with proper observation and response to the situation.
36. What is a legal rule and what is technique?
Training programme requirement
The practical programme covers:
- gear changing appropriate for energy-efficient driving,
- the use of engine braking.
Specific test criterion
For Categories B/B+E:
- changing up at 1800–2600 rpm,
- the first four gears engaged before reaching 50 km/h,
- the use of engine braking.
Obligation under the road traffic law
Among other things, the driver must:
- drive at a speed that ensures control of the vehicle,
- brake in a way that does not cause a hazard to road safety or obstruct traffic.
Good technique
Good practice includes, among other things:
- smooth clutch control,
- matching the gear to the speed and load,
- not pressing the clutch without need,
- avoiding engine speeds that are too high or too low,
- preparing the speed and gear before a bend,
- using an appropriate gear on a descent.
These elements are not separate legal rules prescribing one identical movement for every car model.
37. A simple pattern for changing gear while driving
You can think about changing gear according to the following pattern:
observation → speed and load → choice of gear → smooth change → checking the car's response
Observation
What is happening ahead of the vehicle?
Speed and load
Is the engine running in the right range, and am I about to accelerate, slow down or drive uphill?
Choice of gear
Which gear will be appropriate after the change?
Smooth change
Clutch and gear lever without a jerk or unnecessary delay.
Check
Is the car responding correctly after the change?
38. A simple pattern for anticipated slowing down
When calmly approaching a place where you need to slow down:
look early → ease off the accelerator → slow down in gear → use the brake → select a gear or stop
This order helps you combine:
- observation,
- engine braking,
- the service brake,
- correct gear changing.
However, it is not a rigid algorithm for every situation.
A sudden hazard requires an immediate reaction appropriate to the hazard.
Common pitfalls
1. The range of 1800–2600 rpm is a specific test criterion for changing up in Categories B/B+E. It is not a general rule of the road traffic law assigning gears to every speed.
2. The first four gears must be engaged before reaching 50 km/h when meeting the test criterion. This does not mean that “fourth gear = mandatory 50 km/h”.
3. There is no single universal speed for each gear in all cars.
4. A gear that is too low at high speed may cause very high revs and a jerk.
5. A gear that is too high at low speed may cause the engine to run unevenly and leave no acceleration in reserve.
6. Do not look at the gear lever while driving.
7. After changing gear, your hand goes back to the steering wheel.
8. The clutch is not a second brake.
9. Do not keep your left foot resting on the clutch pedal.
10. During normal slowing down, do not press the clutch automatically right from the start.
11. The regulations do not require you to change down through every gear in turn at every stop.
12. Engine braking is an officially required training and test skill.
13. Engine braking does not replace the service brake when you need to slow down quickly or precisely.
14. On a long descent, an appropriate gear helps you control your speed and limit constant load on the brakes.
15. Rolling with the drive disengaged deprives a manual car of conventional engine braking.
16. On a slippery surface, changing down and releasing the clutch must be particularly smooth.
17. During emergency braking, what matters most is braking effectively, not carrying out a full sequence of downchanges.
18. Select reverse gear in accordance with the vehicle's design after the car has properly stopped.
19. In an automatic, the gearbox changes gear for the driver, but it does not take over responsibility for speed and driving style.
20. Regenerative braking in a hybrid or EV may resemble engine braking, but it does not replace being ready to use the service brake.
Sources
- Rozporządzenie Ministra Infrastruktury i Budownictwa z dnia 4 marca 2016 r. w sprawie szkolenia osób ubiegających się o uprawnienia do kierowania pojazdami, instruktorów i wykładowców, consolidated text: Dz.U. 2018 poz. 1885, as subsequently amended:
- Annex No. 1, part I,
officialTopic 2.9— “Vehicle control techniques”, - Annex No. 1, detailed practical training programme in road traffic, point 2.27 — “Gear changing appropriate for energy-efficient driving”,
- point 2.28 — “Using engine torque while braking — engine braking”.
- Annex No. 1, part I,
- Rozporządzenie Ministra Infrastruktury z dnia 24 listopada 2023 r. w sprawie egzaminowania osób ubiegających się o uprawnienia do kierowania pojazdami, szkolenia, egzaminowania i uzyskiwania uprawnień przez egzaminatorów oraz wzorów dokumentów stosowanych w tych sprawach, Dz.U. 2023 poz. 2659, as subsequently amended:
- Annex No. 1, table of test tasks in road traffic,
- item 26 — gear changing appropriate for energy-efficient driving; for Categories B/B+E, changing up at 1800–2600 rpm and engaging the first four gears before reaching 50 km/h,
- item 27 — using engine torque while braking — engine braking.
- Rozporządzenie Ministra Infrastruktury z dnia 12 stycznia 2024 r., Dz.U. 2024 poz. 56 — amendment to the examination regulations; it did not change the indicated criteria of items 26–27.
- Rozporządzenie Ministra Infrastruktury z dnia 21 maja 2025 r., Dz.U. 2025 poz. 696 — another amendment to the examination regulations; the changes to Annex No. 1 concerned other items, and no change was found to the criteria of items 26–27 used in this lesson.
- Ustawa z dnia 20 czerwca 1997 r. — Prawo o ruchu drogowym, consolidated text Dz.U. 2024 poz. 1251, as subsequently amended:
- Article 19(1) — the obligation to drive at a speed that ensures control of the vehicle, taking traffic conditions into account,
- Article 19(2) point 2 — the obligation to brake in a way that does not cause a hazard to road safety or obstruct traffic.
- Driving-technique / mechanics note:
- how the gear is chosen depends on the design of the gearbox, the engine characteristics, the speed, the load and the driving conditions,
- smooth clutch control, avoiding constantly resting the foot on the clutch pedal, selecting a lower gear before the load increases and preparing the gear appropriately before a bend are driving-technique principles, not separate rules of the road traffic law,
- how the automatic gearbox modes, drivetrain braking and regenerative braking are used depends on the design of the particular vehicle and the manufacturer's recommendations.
- State of the law checked in the official ELI on 22 August 2026; no later amendment to the examination regulations changing the indicated criteria for gear changing and engine braking was found among the current acts.
