The driver’s field of view and blind spots
Contents
The driver cannot see the entire space around the car at the same time.
Part of the surroundings is observed:
- directly through the windows,
- in the mirrors,
- through the reversing camera or camera system,
- after turning the head.
Even so, there may always be areas that are:
invisible or only partially visible.
These are blind spots.
The most important rule in this lesson:
if you cannot see all the space needed to perform a manoeuvre, do not assume it is empty — change your position, use the mirrors, look over your shoulder or wait until you are sure.
1. The driver’s field of view is more than the windscreen
In practice, the observation field consists of several elements:
direct vision
through:
- the windscreen,
- the side windows,
- the rear window;
indirect vision
through:
- the interior mirror,
- the exterior mirrors,
- approved camera systems, if the vehicle is equipped with them;
active checking of the surroundings
by:
- turning your head,
- changing your body position,
- looking again at a previously obscured area.
Safe observation uses all these possibilities.
2. The law requires an adequate field of view
Article 66 of Poland's Prawo o ruchu drogowym (the road traffic law) requires a vehicle to be constructed, equipped and maintained so that using it:
provides the driver with an adequate field of view
and allows easy, convenient and reliable use of the devices for:
- steering,
- braking,
- signalling,
- lighting the road
while observing the road at the same time.
This means that good visibility is not merely a matter of comfort.
It is an element of the vehicle's technical safety.
3. Mirrors are a mandatory part of the vision system
The technical-conditions regulation sets detailed requirements concerning:
- the number,
- type,
- positioning,
- field of view
of mirrors and indirect-vision devices.
In a modern passenger car, the driver primarily uses:
- the interior mirror,
- the left exterior mirror,
- the right exterior mirror.
The detailed type-approval requirements depend, among other things, on:
- the vehicle category,
- the date of first registration,
- the design.
In e-Lectures, you are not required to memorise type-approval tables.
The most important skill is:
correctly adjusting and effectively using the available observation devices.
4. Adjust the mirrors only after adjusting the seat
The field of view in a mirror depends on the position of the driver's head.
Therefore, the correct sequence is:
- adjust the seat,
- adjust the backrest,
- adjust the steering wheel,
- adjust the head restraint,
- adopt your normal driving position,
- only then adjust the mirrors.
If you move the seat after adjusting the mirrors:
→ their adjustment may no longer be correct.
5. The interior mirror should make maximum use of the view through the rear window
In a typical passenger car, adjust the interior mirror so that, without changing your head position, you can see as much of the rear window area as possible.
Do not adjust it for:
- watching passengers,
- looking mainly at the rear seat,
- fixing your hair.
Its primary function while driving is to observe the space behind the vehicle.
6. Side mirrors should complement, not exactly duplicate, the central view
If both exterior mirrors mainly show:
- the side of your own car,
- the same area as the interior mirror,
part of the available field of view is wasted.
In practice, it is worth adjusting them so that:
- a small part of your own vehicle may serve as a reference point,
- as much of the image as possible covers the area beside and behind the car.
There is no single ideal adjustment angle for:
- every driver,
- every car.
7. Correctly adjusted mirrors reduce blind spots — they do not eliminate them completely
This is a key rule.
Even with the mirrors adjusted very well, a vehicle may be:
- outside your direct field of view,
- outside the mirror's current field of view,
- immediately beside the rear corner of the car.
Therefore, before changing lanes it is not enough to say:
“I can't see anything in the mirror.”
You must also check:
the blind spot.
8. Shoulder check
Before a manoeuvre in which a vehicle may be beside you, it is helpful to take a brief look:
over your shoulder in the appropriate direction.
This applies particularly to:
- changing lanes,
- moving off from the kerb,
- turning across a cyclist's path,
- some situations when joining traffic.
Important
The look should be:
- brief,
- deliberate,
- carried out after first checking the situation in front of the car.
Do not look away from the road ahead for several seconds.
9. Sequence before changing lanes
A good observation sequence is:
- check the situation ahead,
- look in the interior mirror,
- look in the relevant exterior mirror,
- check the blind spot,
- signal the manoeuvre in good time,
- reassess the situation,
- change lanes smoothly.
The direction indicator:
→ does not replace observation.
It communicates your intention.
It does not give you priority.
10. A vehicle can “disappear” between the mirror and your side vision
A typical situation:
- a motorcycle is visible in the exterior mirror,
- it approaches,
- it disappears from the mirror,
- the car driver still cannot see it directly beside the car.
This is one of the blind-spot areas.
If you saw a vehicle in the mirror and a moment later you can no longer see it:
→ do not assume that it has turned away or slowed down.
First establish where it is.
11. A motorcycle is particularly easy to overlook
A motorcycle:
- has a smaller profile,
- can quickly change position relative to the car,
- fits more easily into a blind spot.
Before:
- changing lanes,
- turning,
- making a U-turn,
- opening a door,
check the space especially carefully.
12. A cyclist may be close to the right-hand side of the car
Before turning right:
- the right-hand mirror,
- the blind spot,
- the cycle track/lane
should be checked again.
A cyclist may:
- approach on the right,
- legally overtake slow-moving vehicles on the right,
- be so close to the car that they are no longer visible in the mirror.
This links M6.7 with M5.4.
13. The A-pillar creates a real blind spot in front of the driver
The A-pillar is the bodywork element between:
- the windscreen,
- the front door.
It is necessary for structural rigidity, but it may obscure:
- a pedestrian,
- a cyclist,
- a motorcycle,
- part of a car.
This is particularly important:
- at intersections,
- on roundabouts,
- at pedestrian crossings.
14. A small head movement can reveal an object obscured by a pillar
It is not enough to look once from one position.
If a pillar obscures part of an intersection:
- move your head slightly,
- check the space in front of and behind the pillar.
Example
A pedestrian is moving at a similar angular speed to your car.
For a few moments, they may remain:
directly behind the A-pillar.
Only changing your head position will reveal their presence.
15. B- and C-pillars can also obscure road users
The side and rear pillars restrict the view when:
- reversing,
- changing lanes,
- reversing out of a parking space.
Large rear pillars are particularly problematic in:
- SUVs,
- crossovers,
- coupés,
- vans.
Every model's design produces a different field of view.
Therefore, after changing cars:
→ you have to “learn” its blind spots again.
16. A high window line makes low objects harder to see
A modern car may have:
- a high window line,
- a substantial bonnet,
- a high tailgate.
The driver may not be able to see directly:
- a small child,
- a low post,
- a bicycle lying behind the car,
- an animal.
This is particularly important when:
- moving off,
- manoeuvring,
- reversing.
17. The front of the car also has a blind spot
Blind spots do not occur only:
behind and to the sides.
In a high SUV or van, an object very close in front of the bumper may be invisible.
Before moving off after a longer stop in a place where there are:
- children,
- pedestrians,
- animals,
it is worth making sure that the space immediately in front of the car is clear.
18. Reversing presents the greatest problem with a limited field of view
When reversing, the direction of travel is opposite to the driver's natural orientation.
When reversing, Article 23 requires:
- exercising particular caution,
- giving way to other road users,
- checking that there is no obstacle behind the vehicle.
If it is difficult to make sure of this personally:
→ the driver must arrange for another person to assist.
This is one of the few cases where the regulations expressly provide for the assistance of an observer.
19. A reversing camera does not replace the duty to make sure
A camera can be very helpful, particularly for detecting:
- low objects,
- parking-space lines,
- the space immediately behind the vehicle.
However, it may not show everything.
Limitations include:
- a dirty lens,
- rain,
- snow,
- wide-angle image distortion,
- limited coverage,
- poor quality at night.
Therefore, when reversing use:
- the camera,
- the mirrors,
- direct observation,
- sensors,
as one observation system.
20. A wide-angle image can affect distance assessment
Cameras and some mirrors use:
- wide-angle,
- aspherical,
- convex
surfaces or imaging.
This allows more space to be seen.
The trade-off may be:
- altered proportions,
- an object appearing farther away,
- more difficult distance assessment.
Therefore, do not make a decision solely on the basis that:
“it looks far away.”
Also observe:
- how quickly the image is changing,
- the other mirrors,
- the actual space.
21. Parking sensors detect obstacles, but not all of them
An ultrasonic sensor may have difficulty with:
- a very thin post,
- a low object,
- an unusual surface,
- an obstacle outside the sensors' coverage.
Do not reverse “until the continuous tone”, assuming that the system knows the exact position of every object.
Technology is an aid.
It does not remove the need to observe.
22. Blind Spot Monitoring is support, not priority
Blind Spot Monitoring may warn you:
- with a light in the mirror,
- with a signal,
- with a vibration,
that there is a vehicle beside you.
However, it may have limitations with:
- very fast motorcycles,
- dirty sensors,
- unusual road geometry,
- a trailer.
The absence of a warning does not automatically mean:
“the lane is clear.”
Before changing lanes, still:
→ look in the mirrors and check the blind spot.
23. Lane change assist does not perform the observation duty for the driver
The system may:
- warn,
- correct the vehicle's path,
- in some cars assist with changing lanes.
The driver's responsibility for a safe manoeuvre remains.
If the system and your own observation provide conflicting information:
→ do not perform the manoeuvre until you have clarified the situation.
24. Passengers may restrict visibility
A tall passenger or a person sitting in an unusual position may obscure:
- the rear window,
- a side window,
- part of the field of view.
Do not place objects in a way that obstructs observation.
If the people or items being carried affect visibility:
→ make appropriate use of the other observation devices and exercise greater caution.
25. Luggage must not deprive the driver of an adequate field of view
Article 66 requires an adequate field of view.
Therefore, do not arrange:
- boxes,
- bags,
- luggage
so that they dangerously obstruct:
- the windscreen,
- the side windows,
- the space needed for observation.
When a load obscures the rear window, the required exterior mirrors and proper organisation of observation become particularly important.
26. A trailer increases blind spots
A car with:
- a caravan,
- a large cargo trailer
has significantly restricted rearward visibility.
The trailer may completely block the field of view in the interior mirror.
Therefore, particularly important are:
- correctly adjusted exterior mirrors,
- any additional mirrors required by the regulations,
- greater caution when changing lanes and reversing.
27. A large vehicle has much larger blind spots than a passenger car
The driver of:
- a lorry,
- a bus
sits high and uses many mirrors.
Even so, they may have large areas of restricted visibility:
- immediately in front of the cab,
- on the right-hand side,
- along the sides,
- behind the vehicle.
Do not assume:
“they are sitting high, so they can see everything.”
Often the opposite is true.
28. Do not remain alongside a lorry cab for a long time
A particularly dangerous position is:
- on the right-hand side of the lorry,
- near the cab and front axle.
When turning, the lorry may:
- take up more space,
- cross the path of a vehicle beside it.
If you are overtaking:
→ complete the manoeuvre efficiently without remaining unnecessarily in the blind spot.
This does not mean exceeding the permitted speed.
29. “If you cannot see the lorry driver in their mirror” — treat this as a warning
A practical safety rule:
if, while travelling beside a large vehicle, you cannot see its driver in the mirror:
→ there is a significant risk that the driver also has difficulty seeing you through that particular mirror.
This is not a statutory definition of a blind spot.
It is a useful indication:
do not assume that you have been noticed.
30. A bus has particular blind spots at a bus stop
A bus driver must observe:
- vehicles,
- pedestrians,
- passengers,
- mirrors,
- doors.
The bus itself may also obscure pedestrians from the driver of a car travelling beside it.
Therefore, the area around a bus stop requires observation from two perspectives:
- whom the bus may not see,
- whom the bus is obscuring from you.
31. A motorcyclist also has a limited field of view
A helmet:
- should not prevent the required observation,
- but a motorcyclist's field of view and way of checking the surroundings differ from those of a car driver.
A motorcyclist does not have:
- an interior mirror,
- a rear window.
Do not assume that a rider will notice you simply because you are travelling behind them.
Maintain an appropriate distance and a predictable path.
32. A cyclist has different observation options from a car driver
A cyclist may:
- turn their head,
- use a mirror, if fitted,
- listen to the surroundings.
Turning the head may, however, temporarily affect:
- the bicycle's path,
- balance.
If you see a cyclist looking behind:
→ leave them additional space.
33. A parked vehicle can hide an entire road user
A blind spot is not created only by the design of your car.
It may be created by:
- a parked van,
- a lorry,
- a hedge,
- an advertisement,
- a container.
Behind the obstruction there may be:
- a pedestrian,
- a child,
- a cyclist,
- a car emerging from a property.
If the space is obscured:
→ treat it as potentially occupied, not as empty.
34. At an intersection, the field of view must be “opened up” gradually
When visibility is restricted, do not:
- drive the front of the car sharply into the carriageway,
- only then look for traffic.
The correct approach is:
- stop where required by the regulations,
- then, if necessary, edge the vehicle forward very slowly,
- gradually obtain a view,
- stop again if the situation requires it.
Do not, however, cross the point at which you would create a hazard.
35. A traffic mirror is an aid, not a guarantee that the road is clear
At difficult exits, the road authority may install:
a traffic mirror.
Its image may:
- distort distance,
- have limited coverage,
- be dirty,
- be obscured.
Do not make a decision on the basis of a single brief glance in the mirror.
Combine it with:
- direct observation,
- approaching slowly,
- checking again.
36. Rain, fog and night reduce the effective field of view
M6.4 and M6.5 show that even if the vehicle's design allows you to see through the window, information may be limited by:
- rain,
- fog,
- snow,
- darkness,
- glare,
- a dirty windscreen.
We can therefore distinguish between:
the vehicle’s design field of view
and
the effective observation range under the prevailing conditions.
The driver adapts their driving to the latter.
37. Low sun can practically “close off” part of the field of view
Dazzle from the sun occurs particularly:
- in the morning,
- in the evening,
- on a wet road surface.
Helpful measures include:
- a clean windscreen,
- the sun visor,
- suitable glasses, if the driver needs them,
- reducing speed.
If for several seconds you can barely see the road:
→ do not continue at the same speed.
38. Before changing direction, also check the space you intend to enter
A driver may check priority correctly and still overlook:
- a post,
- a traffic island,
- a cyclist,
- a pedestrian,
- a vehicle in the blind spot.
Before turning, observation should include:
- the path in front of the car,
- the side you are turning towards,
- the area beside the vehicle.
Do not look only at vehicles approaching from the opposite direction.
39. On a roundabout, the A-pillar may obscure a vehicle for several moments
On a roundabout, your car and a vehicle travelling around the circulatory carriageway may move relative to each other in such a way that the other car remains:
behind the A-pillar.
Therefore, before entering:
- do not rely on one static glance,
- move your eyes and head,
- reassess the situation immediately before moving off.
40. Do not rely on one glance from several seconds ago
The situation in a blind spot changes very quickly.
A motorcycle travelling at 50 km/h covers almost 14 m in one second.
Therefore:
- looking in the mirror,
- then observing another direction for a long time,
- and then immediately changing lanes
may be dangerous.
Before starting the manoeuvre:
→ carry out an up-to-date check.
41. Scanning the surroundings should be continuous
There is no single rule saying:
“check the mirror exactly every 5 seconds.”
The driver should regularly shift attention between:
- the distance ahead,
- the road immediately ahead,
- the mirrors,
- the sides,
- signs.
The frequency depends on the situation.
Before a manoeuvre, much more intensive checking is needed than during steady driving on an empty road.
42. Do not stare into a mirror for a long time
A mirror is for brief, frequent checks.
If you look exclusively at the view behind for several seconds:
→ during that time, the situation in front of the car may change.
Good observation means:
brief glances + quickly returning your eyes to the road ahead.
43. Other drivers' fields of view may differ from yours
The same road user may be:
- perfectly visible to you,
- completely invisible to the driver of another vehicle.
That is why the principle of limited trust from M5.1 also includes the question:
“can they actually see me now?”
Particularly around:
- lorries,
- buses,
- vehicles with trailers,
- reversing vehicles.
44. Error: “I have priority, so they must have seen me”
Priority does not increase the other driver's field of view.
You may have priority but be:
- behind a pillar,
- in a blind spot,
- behind another vehicle.
If the other vehicle's behaviour indicates that the driver cannot see you:
→ react.
Do not enforce priority by allowing a collision to occur.
45. Technology has limitations — the driver must combine information
A modern car may have:
- 360° cameras,
- blind-spot monitoring,
- parking sensors,
- rear cross-traffic alert,
- automatic braking.
The safest way to use these systems is:
technology + mirrors + direct observation + anticipation
and not:
technology instead of observation.
Step-by-step method for observation before a manoeuvre
Step 1 — check the situation in front of the car
Do you have time to perform the manoeuvre?
Step 2 — check the relevant mirrors
What is happening behind and beside you?
Step 3 — identify where the blind spot is
Could a vehicle have “disappeared” from the mirror?
Step 4 — make a brief direct check
If the situation requires it:
→ look over your shoulder / change your head position.
Step 5 — take design limitations into account
- A-pillar,
- trailer,
- large vehicle beside you.
Step 6 — treat electronic systems as an aid
Not as a guarantee.
Step 7 — check the situation again immediately before performing the manoeuvre
Observation must be up to date.
Common pitfalls
1. The driver's field of view consists of direct vision, mirrors/indirect-vision devices and actively changing the observation point.
2. Article 66 requires the vehicle to provide the driver with an adequate field of view.
3. Mirrors are adjusted after the seat and the driver's position have been correctly adjusted.
4. Correctly adjusted mirrors reduce blind spots but do not guarantee that they are completely eliminated.
5. Before changing lanes, check the mirrors and blind spot; the direction indicator does not give you priority.
6. A motorcycle or cyclist may be in the area between the mirror's field of view and the driver's direct vision.
7. The A-pillar can obscure an entire pedestrian, cyclist, motorcycle or even part of a car.
8. A small change in head position can reveal the space obscured by a pillar.
9. Blind spots also occur immediately in front of and behind a tall vehicle, not only at the sides.
10. When reversing, if the driver cannot personally make sure that there is no obstacle behind the vehicle, Article 23 requires them to arrange for another person to assist.
11. A reversing camera, sensors and blind-spot monitoring are aids — they do not replace the driver's observation and duties.
12. A trailer can significantly increase blind spots and completely block the view in the interior mirror.
13. A lorry and bus have significantly larger blind spots than a typical passenger car.
14. If another driver's behaviour indicates that they cannot see you, having priority should not prevent you from taking defensive action.
15. There is no rule requiring you to look in the mirrors every specified number of seconds — observation should be regular and adapted to the situation.
Sources
- Rozporządzenie w sprawie szkolenia osób ubiegających się o uprawnienia do kierowania pojazdami:
- Annex No. 1,
officialTopic 2.7— “Different driver fields of view”.
- Annex No. 1,
- Ustawa z dnia 20 czerwca 1997 r. — Prawo o ruchu drogowym:
- Article 23(1) point 3 — particular caution when reversing, the duty to give way and to check the space behind the vehicle; if it is difficult to make sure personally — the duty to arrange for another person to assist,
- Article 22 — rules for changing direction and changing lanes,
- Article 66(1) point 5 — requirement for an adequate field of view for the driver and the ability to operate vehicle controls while observing the road at the same time.
- Rozporządzenie Ministra Infrastruktury w sprawie warunków technicznych pojazdów oraz zakresu ich niezbędnego wyposażenia:
- Annex No. 12 — detailed requirements concerning the equipment of motor vehicles with mirrors,
- Annex No. 13 — the minimum required field of view in a specified exterior mirror for the indicated vehicle category,
- provisions concerning learner vehicles provide for additional mirrors for the instructor.
- Teaching note:
- a blind spot is an area invisible or insufficiently visible from the driver's normal position using the available windows/mirrors,
- wide-angle cameras and mirrors can alter the perception of distance,
- BSM systems, sensors and cameras are assistance systems and may have technical limitations,
- the position and size of blind spots depend on the design of the specific vehicle and the driver's position.
- Current requirements concerning the field of view and mirrors: technical conditions (Dz.U. 2024 poz. 502) and the road traffic law.
