Category BM7.1
Lesson 1 of 6

Driving position and preparation for driving

Contents

Vehicle control begins before the car moves off.

If the driver sits too far from the pedals or too close to the steering wheel, has badly adjusted mirrors or has to lift their back off the backrest to make a larger steering movement, they make it harder for themselves to:

  • observe the road,
  • steer precisely,
  • brake quickly and firmly,
  • fully depress the clutch in a car with a manual gearbox,
  • check the space behind the vehicle,
  • benefit from a correctly working seat belt and head restraint.

This is why setting up the driving position is neither cosmetic nor a matter of comfort.

It is part of safe driving technique.


1. What exactly follows from the official programme?

In the theoretical training programme, topic 2.9 is simply called:

“Vehicle control techniques”.

This wording alone does not give one official method of adjusting the seat or holding the steering wheel.

A more detailed point of reference can, however, be found in the practical training programme.

For preparing to drive, the programme includes, among other things:

  • adjusting the seat,
  • adjusting the mirrors,
  • adjusting the head restraints,
  • fastening the seat belts,
  • making sure that the vehicle's doors are closed.

This shows that correctly setting up the driver's position is officially treated as part of the skill of driving a vehicle.


2. The practical exam also checks the driver's preparation

The current examination regulations for a car require the following before the drive begins:

  • correct adjustment of the seat,
  • correct adjustment of the mirrors,
  • correct adjustment of the head restraint,
  • fastening the seat belt, if the vehicle is fitted with one,
  • making sure that the vehicle's doors are closed.

The examination regulations also specify the expected result of adjusting the mirrors:

  • in the left mirror, the driver should see the left side of the vehicle and the space behind it on the left,
  • in the right mirror — the right side of the vehicle and the space behind it on the right,
  • in the interior mirror — the space behind the vehicle, through the rear window.

For the head restraint, the test criterion specifies a position close behind the head, at head height.

These are specific test requirements, not just general advice about comfort.


3. The law does not set one mandatory seat angle or hand position

This is a very important distinction.

The law does not say, for example:

“the backrest must be set at an angle of exactly X degrees”

or:

“the steering wheel must always be held with the hands in exactly one specified position”.

Such matters belong above all to driving technique and ergonomics.

Drivers differ in:

  • height,
  • leg length,
  • arm length,
  • build,
  • range of movement,
  • the design of the car they drive.

This is why the correct position is a functional position:

you must be able to observe the road freely and operate all the controls needed to drive the car confidently.


4. Make the adjustments in the correct order

The most logical order for setting up the driving position is as follows:

seat → backrest → steering wheel → head restraint → mirrors → seat belt → door check

Why should the mirrors not come first?

Because their setting depends on the position of your head.

If you adjust the mirrors first and then:

  • move the seat,
  • raise the seat cushion,
  • change the backrest angle,

your observation point will change as well.

The mirror setting may then no longer be correct.


5. First set the distance between the seat and the pedals

The driver should sit so that they can operate the pedals confidently through their full range of travel.

In a car with a manual gearbox, this also means being able to fully depress the clutch pedal.

Good practice is to set the seat so that, at the maximum pedal travel needed, the leg is not completely straight and locked at the knee.

Why leave a slight bend?

It helps you to:

  • keep control of the pedal,
  • move quickly between the pedals,
  • press the brake hard when the situation requires it,
  • avoid having to slide your pelvis forwards when operating the pedals.

This is good driving-technique practice — not a statutory requirement specifying a particular knee angle.


6. Do not sit so far back that you “reach” the pedals with the tip of your foot

If the seat is too far back:

  • you may have trouble fully depressing the clutch,
  • you may press the brake less firmly or more slowly,
  • your body may move away from the backrest when you press a pedal,
  • the precision of your footwork decreases.

In an emergency, you should not first have to search for the full travel of the brake pedal.

Your position should allow you to brake decisively without changing the way you sit.


7. A position that is too close is also incorrect

Moving the seat very close to the steering wheel does not automatically improve control.

It may cause:

  • the legs to be bent too much,
  • the knees to catch on the steering wheel or parts of the dashboard,
  • restricted freedom of arm movement,
  • awkward pedal work,
  • too little space between the driver and the steering wheel.

In a car fitted with an airbag, also remember that the airbag is designed to work together with a correctly adopted position and a fastened seat belt.

So do not sit unnecessarily close to the steering wheel.


8. Set the seat height so that you can see the road well

If the car allows the seat height to be adjusted, the setting should provide:

  • a good field of view through the windscreen,
  • the ability to see the instruments,
  • adequate headroom,
  • free leg movement,
  • no contact between the thighs or knees and the steering wheel that hinders steering.

There is no single correct height for every person and every vehicle.

What matters most is the result:

seeing the road and being able to control the car freely.


9. The backrest should support the driver, not force them to reach

Set the backrest so that during normal driving:

  • your back remains supported,
  • your shoulders do not constantly have to come away from the backrest,
  • your hands can move the steering wheel freely,
  • you do not have to lean your whole upper body forwards to carry out a manoeuvre.

Backrest reclined too far

This may make it necessary to:

  • straighten your arms,
  • lift your back off the seat,
  • lean towards the steering wheel during a larger turn.

Backrest too upright and too close

This may restrict arm movement and cause unnecessary tension.

The correct setting should allow you to control the car without fighting your own position.


10. Adjust the steering wheel only after adjusting the seat

If the vehicle allows the steering wheel to be adjusted for height, or for height and reach, it can be matched to the driver's position.

The steering wheel should be positioned so that:

  • it can be operated freely through the full range needed,
  • the arms remain slightly bent,
  • the steering wheel does not get in the way of the legs,
  • it does not unnecessarily hide the most important gauges,
  • the driver does not have to lean forwards.

Once again:

the regulations do not specify one mandatory steering-wheel setting in centimetres.

What matters is the ability to steer confidently while observing the road properly.


11. Article 66 describes a function the vehicle must provide

Poland's Prawo o ruchu drogowym (the road traffic law) requires a vehicle taking part in traffic to be constructed, equipped and maintained so that it provides the driver with:

  • an adequate field of view,
  • easy, convenient and reliable use of the devices for steering,
  • use of the devices for braking,
  • use of the devices for signalling and lighting the road,
  • all while observing the road at the same time.

From 24 June 2026, the current wording of Article 66(1) point 5 contains a technical exclusion concerning a fully automated vehicle.

For an ordinary Category B car driven by a driver, the meaning of the provision remains the same:

the driving position and the vehicle's devices must allow the driver to observe the road and control the car confidently.


12. Hands on the steering wheel — separate the rule from good practice

There is no legal rule requiring the hands to be held in exactly one numerically defined place on the steering wheel throughout the drive.

Modern driving technique usually favours placing the hands on both sides of the steering wheel, roughly on its side sections, often described by convention as around “9 and 3”.

Why?

This position makes it easier to:

  • make small corrections precisely,
  • start turning quickly in either direction,
  • avoid unnecessary repositioning of the hands during normal driving,
  • keep symmetrical control of the steering wheel.

We treat “9 and 3” as popular good practice, not as a legal rule.

If the manufacturer of a particular vehicle gives specific recommendations on the driving position, they should be taken into account.


13. Do not rely on one hand for steering without good reason

During steady driving, steering with one hand may seem comfortable.

The problem arises when you suddenly have to:

  • avoid an obstacle,
  • correct your path,
  • react to a gust of wind,
  • carry out a quick defensive manoeuvre.

Two hands on the steering wheel usually give greater control and a larger margin for reaction.

Of course, when you operate some of the car's controls, one hand may briefly leave the steering wheel.

This does not change the technical principle:

when there is no reason to do something else, the driver should keep the fullest possible control of the steering wheel.


14. Adjust the head restraint after the seat and backrest

The position of the head restraint depends on the position of the head.

This is why it is checked after the seat and backrest have been adjusted.

The current test criterion requires the head restraint to be set:

close behind the head, at head height.

It should not sit low behind your neck just because the previous driver left it there.

We have already covered the detailed role of the head restraint in reducing neck injuries in M4.5 Seat belts and head restraints.

What matters most here is the order:

set your position → only then adjust the head restraint


15. Adjust the mirrors from your normal driving position

After adjusting the seat, backrest, steering wheel and head restraint, sit in your normal driving position.

Only then adjust the mirrors.

Do not lean specially while adjusting them if you will later sit differently while driving.

A mirror should show the area you need when you are sitting exactly as you will actually drive the car.


16. Interior mirror

The current test criterion requires the driver to see the space behind the vehicle through the rear window in the interior mirror.

In practice, set the mirror so that it frames the rear window as naturally as possible, without you having to move your head every time you look.

Do not aim it mainly at:

  • passengers' faces,
  • part of the headlining,
  • the inside of the car.

Its main function while driving is to observe traffic behind the vehicle.


17. Exterior mirrors

The examination regulations describe the expected result simply:

  • left mirror → the left side of the car and the space behind the vehicle on the left,
  • right mirror → the right side of the car and the space behind the vehicle on the right.

In practice, the aim is the most useful combination of:

  • orientation relative to your own car,
  • a wide view of the space beside and behind it.

If you angle the mirrors too far inwards, you may mainly see the side of your own car at the expense of the space where other road users are moving.

If you angle them too far outwards without any reference to the car, you may make it harder to judge the vehicle's position during manoeuvres.

The setting must be functional for the particular car.


18. Correctly set mirrors do not remove all blind spots

Even well-adjusted mirrors do not guarantee visibility of the whole space around the vehicle.

There remain areas that the driver may not be able to see:

  • in the interior mirror,
  • in an exterior mirror,
  • directly through the windows from the normal head position.

This is why an additional direct check may be necessary before changing lanes or carrying out another manoeuvre.

We covered this topic in detail in M6.7 The driver’s field of view and blind spots.

Well-adjusted mirrors reduce the blind-spot problem — they do not eliminate it completely.


19. Seat belt — here we have a direct statutory obligation

Unlike the backrest angle or the position of the hands on the steering wheel, using a seat belt is not merely good practice.

Article 39(1) of the road traffic law provides, as a general rule, that:

the driver of a motor vehicle and a person carried in such a vehicle fitted with seat belts are required to use them while driving.

The Act provides for certain exceptions, which we covered earlier in the lesson on seat belts.

For a typical Category B learner, the rule is simple:

fasten your seat belt before you start driving.


20. The “click” of the buckle is not everything

Technically, the seat belt should be positioned so that it can work properly with the driver's body.

Good practice is to check that:

  • the belt is not twisted,
  • the lap section runs low across the hips, not high across the soft part of the abdomen,
  • the shoulder section runs across the shoulder and chest,
  • the belt is not under the arm or behind the back,
  • excessively thick clothing or objects do not interfere with its correct positioning.

If the car has height adjustment of the upper belt anchorage, it can be matched to the driver's position.

These are rules for using the seat belt safely — they should not be turned into fictitious “centimetre” test requirements that the regulations do not specify.


21. Check that the doors are closed

The practical training programme and the test criteria require you to make sure before driving that the vehicle's doors are closed.

A modern car may indicate a door that is not fully closed by:

  • a dashboard warning light,
  • a message on the instrument cluster,
  • an audible signal.

However, the electronics should not be treated as a reason to skip the check.

Before moving off, the driver should be certain that:

  • their own door is properly closed,
  • the passengers' doors are not left ajar,
  • no part of the vehicle remains open in a way that could create a hazard.

22. Tidy the space around the driver

During sudden braking or a manoeuvre, a loose object in the cabin may:

  • shift,
  • slide under the pedals,
  • distract the driver,
  • hit someone inside the vehicle.

This is why, before driving, it is worth removing from the pedal area any objects that could interfere with operating the pedals.

This also applies to a badly positioned floor mat that may slide under a pedal.

The detailed rules on load and securing carried objects will be covered in Module 11.

Here, remember the technical principle:

nothing should prevent full use of the brake, the clutch or the accelerator pedal.


23. Make sure you know where the car's basic controls are

Before moving off in a car you have not driven before, check the position of the most important controls.

In particular:

  • the brake pedal,
  • the accelerator pedal,
  • the clutch — if there is one,
  • the gear lever or gear selector,
  • the parking brake,
  • the indicators,
  • the lights,
  • the wipers and washers,
  • the horn,
  • the hazard warning lights.

Cars differ in where some of the controls are located.

An emergency is not a good time to look for the hazard warning light switch or to work out how to switch on the wipers.


24. Manual and automatic cars require different footwork

Manual gearbox

The driver uses:

  • the clutch,
  • the brake,
  • the accelerator pedal.

The driving position must allow full operation of all three pedals.

Automatic gearbox

The driver operates:

  • the brake,
  • the accelerator pedal.

As a rule, both pedals are operated with the right foot.

The left foot is kept away from the pedals, unless the design of the particular vehicle and the manufacturer's instructions specify otherwise.

Do not carry footwork over from a manual gearbox to an automatic without thinking.

We will cover moving off and pedal control in detail in M7.2.


25. Do not start driving while adjusting the seat or mirrors

Make adjustments before moving off.

Moving the seat or making extensive mirror adjustments while driving means that part of the driver's attention is no longer directed at the road.

In addition, a sudden change in seat position may make it harder to:

  • reach the pedals,
  • control the steering wheel,
  • use the mirrors.

If, after moving off, you notice that the setting is clearly wrong:

→ stop in a safe place where stopping is permitted and correct it.


26. Do not copy the previous driver's settings

The fact that the previous person drove the car with a particular setting does not mean it will be correct for you.

After a change of driver, check at least:

  • the seat distance,
  • the seat height,
  • the backrest,
  • the head restraint,
  • the steering wheel,
  • the mirrors.

A particularly large difference in height between drivers may completely change:

  • access to the pedals,
  • the position of the hands,
  • the field of view.

27. A stored seat setting does not exempt you from checking

Some cars have electric seats and seat memory for the driver's position.

This is a convenient solution, but after automatic adjustment it is still worth checking:

  • whether the seat has actually stopped in the right position,
  • whether the steering wheel is set correctly,
  • whether the mirrors match your current position,
  • whether any element has been changed by another user.

Automation can restore a stored setting.

However, it will not judge for the driver whether the position is still correct and safe.


28. Camera systems do not replace correctly adjusted mirrors

The car may have:

  • a reversing camera,
  • 360° cameras,
  • blind-spot monitoring,
  • a digital rear-view mirror,
  • rear cross-traffic alert.

These are assistance systems.

They should not lead to neglecting the basic set-up of the driving position.

In a vehicle fitted with conventional mirrors, the mirrors must be correctly adjusted and used as intended.

Electronic systems may have:

  • a limited field of view,
  • a dirty camera,
  • image delay or distortion,
  • operating limitations described by the manufacturer.

29. A correct position helps during emergency braking

In M6.2 we covered stopping distance and braking technique.

What matters here is how these topics connect.

If the driver is sitting correctly:

  • they can quickly move the right foot to the brake,
  • they can press the pedal decisively,
  • their back is supported,
  • they can control the steering wheel at the same time.

If the seat is too far back, hard braking may require the whole body to slide forwards.

This costs time and precision.


30. A correct position also helps during a defensive manoeuvre

Suddenly avoiding an obstacle requires fast hand movements while keeping the upper body under control.

If the driver:

  • sits too far back,
  • has straight arms,
  • has to lift a shoulder off the backrest,

the range and precision of steering movements may be worse.

This is why ergonomics is directly linked to safety.

It is not about a “sporty” driving position.

It is about a position that lets you quickly use the car's full capabilities when a hazard appears.


31. Comfort matters, but it must not mean relaxing control

On longer journeys, the position should be comfortable enough not to cause rapidly increasing fatigue.

However, do not confuse comfort with a position:

  • that is half-reclined,
  • with one hand constantly resting on the top of the steering wheel,
  • with the seat pushed very far back,
  • that requires leaning forwards for every larger steering movement.

A good position combines:

comfort + support + freedom of movement + control.


32. Judge every adjustment by its effect

Do not just memorise a mechanical instruction:

“move the seat by this much”

or:

“set the backrest at this angle”.

It is better to check the result.

Pedals

Can you use them through their full range without moving your body?

Steering wheel

Can you make the necessary movement freely without straightening your arms or lifting your back?

Visibility

Can you see the road, the gauges and the mirrors well?

Head restraint

Is it close behind your head and at head height?

Seat belt

Is it fastened and positioned correctly?

If the answer to any of these points is no:

→ your position needs correcting.


33. Minimum preparation sequence before moving off

Before you start driving, you can use a simple routine:

Step 1 — seat

Set the distance and height so that you can use the pedals freely and observe the road.

Step 2 — backrest

Make sure your upper body is supported and you can reach the steering wheel.

Step 3 — steering wheel

If it is adjustable, match its position to your driving position.

Step 4 — head restraint

Set it close behind your head, at head height.

Step 5 — mirrors

Adjust them from your normal driving position.

Step 6 — seat belt

Fasten it and check its position.

Step 7 — doors and the space around the pedals

Make sure the doors are closed and that nothing interferes with operating the pedals.

Step 8 — controls

If you do not know the car, locate the most important controls before moving off.

Only then do we move on to starting the vehicle and moving off, which we will cover in the next lesson.


Common pitfalls

1. There is no statutory “magic angle” for the seat and no single mandatory hand position on the steering wheel. These are elements of driving technique, which we judge by their function.

2. The practical training programme officially covers adjusting the seat, mirrors and head restraint, fastening the seat belt and checking that the doors are closed.

3. The current practical exam also checks these actions before the drive begins.

4. The seat is adjusted before the mirrors. A change in the driver's position changes the observation point in the mirrors.

5. The driver should be able to use the pedals through their full range without sliding the body forwards.

6. Setting the seat too far back may make full braking and clutch operation more difficult.

7. A position that is too close restricts leg and arm movement and may put the driver unnecessarily close to the steering wheel.

8. “9 and 3” is good practice in modern driving technique, not a legal rule requiring an exact hand position.

9. We check the head restraint after adjusting the seat and backrest. Test criterion: close behind the head, at head height.

10. The mirrors should show the space behind and beside the vehicle, but even a correct setting does not remove all blind spots.

11. Fastening the seat belt is a statutory obligation under Article 39, not merely a driving-technique recommendation.

12. Simply fastening the buckle does not replace positioning the belt correctly.

13. The programme and the exam require you to make sure before driving that the vehicle's doors are closed.

14. Nothing should hinder full use of the pedals.

15. Adjust the seat and mirrors before driving; if they need significant correction after moving off, stop in a safe place.

16. Seat memory, cameras and blind-spot monitoring are aids — they do not replace correct set-up of the driving position.

Sources
  • Rozporządzenie Ministra Infrastruktury i Budownictwa z dnia 4 marca 2016 r. w sprawie szkolenia osób ubiegających się o uprawnienia do kierowania pojazdami, instruktorów i wykładowców, consolidated text: Dz.U. 2018 poz. 1885, as subsequently amended:
    • Annex No. 1, part I, officialTopic 2.9 — “Vehicle control techniques”,
    • Annex No. 1, part II, point 1.1.2 — adjusting the seat, mirrors and head restraints, fastening the seat belts and making sure that the vehicle's doors are closed,
    • part II, point 1.2 et seq. — elements of practical vehicle control used to design the subsequent lessons of Module 7.
  • Rozporządzenie Ministra Infrastruktury z dnia 11 października 2023 r., Dz.U. 2023 poz. 2317 — the amendment concerns the rules for training soldiers in voluntary basic military service and does not change officialTopic 2.9 or the indicated scope of Annex No. 1.
  • Rozporządzenie Ministra Infrastruktury z dnia 24 listopada 2023 r. w sprawie egzaminowania osób ubiegających się o uprawnienia do kierowania pojazdami, szkolenia, egzaminowania i uzyskiwania uprawnień przez egzaminatorów oraz wzorów dokumentów stosowanych w tych sprawach, Dz.U. 2023 poz. 2659, as subsequently amended:
    • pre-drive preparation criteria — correct adjustment of the seat, mirrors and head restraint, fastening the seat belt and making sure that the vehicle's doors are closed,
    • criteria for the field of view in the mirrors and for the head-restraint setting.
  • Ustawa z dnia 20 czerwca 1997 r. — Prawo o ruchu drogowym, consolidated text Dz.U. 2024 poz. 1251, as subsequently amended:
    • Article 39(1) — the obligation of the driver and of a person carried in a vehicle fitted with seat belts to use them while driving, subject to the statutory exceptions,
    • Article 66(1) point 5 — the requirement for an adequate field of view and easy, convenient and reliable use of the devices for steering, braking, signalling and lighting while observing the road at the same time; the current wording from 24 June 2026 includes the exclusion concerning a fully automated vehicle.
  • Ustawa z dnia 21 listopada 2025 r. o zmianie ustawy — Prawo o ruchu drogowym oraz niektórych innych ustaw, Dz.U. 2025 poz. 1843 — amendment to the current wording of Article 66(1) point 5.
  • Teaching / driving-technique note:
    • there is no single statutory seat angle, knee angle or mandatory numerical position of the hands on the steering wheel,
    • a setting that allows full operation of the pedals while keeping the body supported and the limbs slightly bent is treated as good driving-technique practice,
    • placing the hands around the side sections of the steering wheel (“9 and 3”) is presented as modern good practice, not as a legal standard,
    • detailed recommendations for a specific vehicle model may come from the manufacturer's instructions.
  • State of the law checked in ELI on 22 August 2026.
↑