Low-speed manoeuvring, parking and hill starts
Contents
Manoeuvring at low speed may seem easier than ordinary driving. The car is moving slowly, so the driver has more time to react.
Yet this is exactly when other difficulties arise:
- you have to judge the position of the whole vehicle very precisely,
- the front and rear wheels follow different paths,
- the front of the car may swing out towards the outside of the turn,
- visibility right next to the vehicle is limited,
- a pedestrian or another vehicle may appear very close,
- the driver's obligations when reversing are particularly strict,
- on a hill, the car may start to roll in the opposite direction.
This is why good manoeuvring technique rests above all on three principles:
low speed → continuous observation → the ability to stop immediately.
In Module 3 we already covered the rules on reversing, stopping and parking. We will not repeat them in full here. We will focus on the technique of driving the car during tight manoeuvres and on the current training and test requirements.
1. Low speed does not mean low risk
When parking or reversing, the speed is low, but the distances from obstacles are small too.
A few or a few dozen centimetres may decide whether the car:
- fits into the parking space,
- clips another vehicle with a corner,
- mounts the kerb,
- knocks over a cone,
- ends up in a pedestrian's path.
At higher speed, the driver concentrates mainly on what is happening ahead of the vehicle.
When manoeuvring, you have to monitor at the same time:
- the front,
- the rear,
- both sides,
- the corners of the car,
- the surroundings outside the field of view of the mirrors.
This is why driving slowly should not lead to relaxed attention.
2. Assess the space first, and only then move off
Before starting a tight manoeuvre, it is worth answering a few questions:
- Is the manoeuvre permitted here?
- Do I have enough space for the whole car?
- Are there pedestrians, cyclists or other vehicles around?
- Which part of the car will come close to an obstacle first?
- Will I be reversing?
- Is visibility adequate?
If the answer to the last question is “no”, the manoeuvre should not be carried out on the basis of an assumption alone.
When reversing, Poland's Prawo o ruchu drogowym (the road traffic law) requires you to make sure that there is no obstacle behind the vehicle. If the driver has difficulty making sure of this personally, they are obliged to arrange for another person to assist.
3. During a manoeuvre, keep to a speed at which you can stop the car immediately
There is no single statutory speed in km/h for parking.
Good technique, however, means operating the car in such a way that:
- the path can be corrected continuously,
- the driver has time to observe the surroundings,
- stopping before an obstacle is possible almost immediately.
In practice, this usually means a very low speed.
If the car starts moving faster than you can precisely control its position:
→ slow down or stop and reassess the situation.
4. In a manual car, the clutch helps you control very low speed
During normal driving, once you have moved off, the clutch should be fully released.
During very slow manoeuvring, the situation is different. In a car with a manual gearbox, brief use of the partial clutch engagement range may help you:
- start moving gently,
- move very slowly,
- meter the drive precisely when parking.
This does not mean, however, that the car should be held at the biting point for a long time.
Prolonged clutch slip:
- increases clutch wear,
- may cause components to overheat,
- is not needed during ordinary driving.
Good practice: use the clutch precisely when the manoeuvre requires it, but do not treat driving with the clutch partly depressed as a normal way of moving.
5. The brake is the basic tool for controlling the pace of a manoeuvre
In a confined space, the driver should be ready to stop immediately.
In a manual car, this means appropriate coordination of:
- the clutch,
- the brake,
- if necessary, a small amount of accelerator.
In an automatic or electric car, how the vehicle behaves after the brake is released depends on the design and settings.
Some cars:
- start to creep very slowly,
- stay stationary thanks to the Auto Hold function,
- slow down more strongly when you lift off the accelerator,
- use regenerative braking.
This is why, after changing cars, you first need to learn how the car responds at low speed.
6. Do not automatically carry habits over from one car to another
Cars differ, among other things, in:
- length,
- width,
- wheelbase,
- turning radius,
- the position of the axles relative to the body,
- clutch response,
- the strength of the power steering,
- how the automatic gearbox works,
- cameras and sensors.
A technique that let you park one car using a specific “point in the mirror” may not work in another.
This is why, rather than memorising one reference point, it is more important to understand:
how the whole body of the car moves during a turn.
7. The rear wheels do not follow exactly in the tracks of the front wheels
During a tight turn, the front wheels set the direction, but the rear wheels follow a path further inside.
This means that the car may:
- pass a kerb with its front,
- and then catch it with a rear wheel.
The same applies to:
- posts,
- corners of walls,
- parked cars,
- traffic islands.
We already met this phenomenon in M7.4. In parking and manoeuvring it is particularly important, because the distances are very small.
8. The front of the car may swing out
If, when reversing, you turn the wheels to the right:
- the rear of the vehicle starts to head to the right,
- the front swings out to the left.
If you turn to the left, the situation is reversed.
This means that watching only the direction in which the rear of the car is moving is a mistake.
During the manoeuvre, you must also monitor the opposite front corner.
Example
You are reversing to the right into a parking space.
There is a car parked on your left.
The possible hazard is not only behind you. The left front of your car may come close to the vehicle standing alongside as you turn.
9. Stopping and reassessing the situation are part of good technique
If you lose confidence during a manoeuvre:
→ stop the car.
You can then:
- check the mirrors,
- reassess the distance,
- see whether a pedestrian has appeared,
- correct the vehicle's position.
In real traffic, there is no prize for completing a difficult parking manoeuvre in one continuous movement.
Safety is more important than looking impressive.
10. Reversing — the statutory obligations still apply when parking
Reverse parking is not an exception to Article 23 of the road traffic law.
When reversing, the driver must:
- give way to other vehicles and road users,
- take particular caution,
- check whether the manoeuvre will cause a hazard or obstruct traffic,
- make sure that there is no obstacle behind the vehicle,
- if it is difficult to make sure personally, arrange for another person to assist.
We covered the detailed rules on reversing and the places where it is prohibited in M3.9.
The most important conclusion here is:
when manoeuvring in reverse, you cannot shift responsibility onto a camera, a sensor or a person standing nearby.
11. Mirrors, rear window, camera and sensors should complement each other
The current Category B test criterion for driving in reverse along a lane requires the path to be observed through the rear window and in the mirrors.
In a car fitted with a reversing camera, the camera can be a great help, but it should not be the only source of information.
The camera may:
- not cover the whole surroundings,
- distort distances,
- be dirty,
- not show an object approaching from the side.
Sensors also have limitations.
Good technique: keep changing the direction in which you look and build a picture of the situation from several sources.
12. Parking begins with choosing a legal place
The ability to position the car technically does not matter if the driver chooses a place where parking is prohibited.
We covered the rules on stopping and parking in detail in M3.3.
The most important rule of Article 46 is that stopping and parking are permitted only in a place and in conditions in which the vehicle:
- is visible to other drivers from a sufficient distance,
- does not cause a hazard to road safety,
- does not obstruct traffic.
The driver is also obliged to use the method of stopping or parking indicated by signs.
This is why, before you start parking, check:
- upright road signs,
- road markings,
- how the parking space is marked out,
- prohibitions arising directly from the legal rules,
- whether, once parked, the car will block other road users.
13. Category B exam — parking takes place in road traffic
This is an important distinction.
In the Category B state practical exam, parking is not a separate parking task carried out in the manoeuvring area.
In road traffic, the candidate carries out one of the following variants:
Perpendicular parking
entering forwards → exiting in reverse
Angled parking
entering forwards → exiting in reverse
Parallel parking between two vehicles
entering in reverse → exiting forwards
The examiner indicates the place.
The current criteria allow one correction of the vehicle's path for each of these variants.
Do not confuse these rules with the parking tasks carried out in the manoeuvring area for other driving-licence categories.
14. In the exam, parking must still comply with the road traffic rules
The examination regulations expressly require parking to be carried out in compliance with the road traffic rules.
In perpendicular and angled parking, once the car is parked it must be possible for the driver and a passenger to get out of the vehicle on both sides.
In parallel parking:
- the space between the vehicles is about twice the length of the driving-test vehicle,
- once parked, the vehicle must not create a hazard to road safety,
- if the car is being positioned parallel to the kerb, it must not mount the kerb during the manoeuvre.
The current Category B criterion does not specify one universal distance from the car to the kerb in centimetres to be memorised as an “exam number”.
What counts is positioning the vehicle correctly, safely and in compliance with the legal rules.
15. Do not learn parking only through “magic points”
During training, the instructor may point out characteristic reference points, e.g. the moment when:
- a particular part of the neighbouring vehicle appears in the window,
- the parking-space line is in a particular place in the mirror,
- you should start turning.
Such points can be very helpful in a particular car.
However, they are neither legal rules nor universal geometry that applies to every car.
After a change of:
- car model,
- seat setting,
- mirror setting,
- vehicle length,
- turning radius
the same points may lead to a different path.
This is why, in addition to reference points, you need to understand what happens to the vehicle after every steering movement.
16. Perpendicular parking — the technical principle
In perpendicular parking, the most important thing is to start turning at a point that gives the car room to position itself between the lines or the neighbouring vehicles.
A general model may look like this:
assessing the space → positioning for the manoeuvre → low speed → turning → checking both sides → straightening → stopping
Assessing the space
Check whether the parking space is large enough and legal.
Positioning for the manoeuvre
Leave yourself enough room for the front and rear of the vehicle to make the necessary arc.
Turning
Guide the car into the parking space at a very low speed.
Checking the sides
Do not watch only one line. Check whether the whole car fits between the boundaries of the space.
Straightening
At the right moment, reduce the steering so that you finish the manoeuvre with the wheels and the body aligned with the parking space.
This is a technical model, not a rigid algorithm counted in steering-wheel turns.
17. Exiting in reverse from a perpendicular space — visibility increases gradually
When reversing out of a space between cars, the driver often cannot see the whole aisle straight away.
This is why you should:
- assess the surroundings before moving off,
- reverse very slowly,
- check both directions again as the rear of the car emerges,
- give way to road users in the path of the reversing car,
- remember that the front of the vehicle swings out during the turn.
Do not pull out abruptly just to “see the road sooner”.
18. Angled parking
Angled parking usually requires less change of direction than perpendicular parking, but you still need to monitor:
- the corner of the parking space,
- the distance from the car standing on the inside of the turn,
- the swing of the opposite side of your own car,
- the final position within the space.
In the Category B exam, the current variant is:
entering forwards → exiting in reverse.
Here too, one correction of the path is allowed.
19. Parallel parking in reverse — why does reversing make positioning the car easier?
When entering in reverse, you can guide the rear wheels relatively precisely into the space at the edge of the carriageway and then position the front of the car.
A general technical model:
positioning beside the space → reversing with steering → checking the rear corner → changing the direction of steering → parallel position → correcting the position
What matters most is understanding the geometry:
- the rear of the car heads in the direction of the steering,
- the front swings out in the opposite direction,
- the car's position must be monitored throughout the manoeuvre.
There is no single universal number of steering-wheel turns, and no single point that works identically in every car.
20. A correction of the path is not a failure
In real traffic, a correction may be the safest decision.
If you can see that:
- the car is going in at the wrong angle,
- the gap on one side is too small,
- you are unsure about clearance at one of the car's corners,
stop and correct the position.
In the Category B state practical exam, the current criteria allow one correction of the vehicle's path during the parking manoeuvre carried out.
This does not mean, however, that in everyday life you may make any number of movements without observing your surroundings. Every further change of direction must still be safe and comply with the legal rules.
21. When parking, check the space needed to open the doors
Positioning the car correctly is not only about the body fitting between the lines.
It is worth leaving reasonable space:
- for the driver,
- for passengers,
- for people in neighbouring cars.
The current Category B test criteria for perpendicular and angled parking require that, once parked, the driver and a passenger can get out of the vehicle on both sides.
In everyday traffic, a similar margin also reduces the risk of damaging the doors of neighbouring vehicles.
22. The kerb is not an “end-of-manoeuvre sensor”
Do not deliberately drive up to an obstacle until you touch it just to establish the vehicle's position.
This applies to:
- a kerb,
- a wall,
- a post,
- another car.
For parallel parking in the exam, the current criterion expressly states that you must not mount the kerb while carrying out the manoeuvre.
In normal driving, too, you should leave a controlled gap and not use contact with an obstacle as a way of positioning the car.
23. A pedestrian may appear in a space that was empty a moment ago
A car park is an environment with many potential conflicts at low speed.
Between vehicles, there may suddenly appear:
- children,
- people with pushchairs or wheelchairs,
- cyclists,
- scooter users,
- people taking things out of the boot.
This is why observation cannot be done only once before starting the manoeuvre.
It must be repeated throughout parking or pulling out.
24. After parking, the car must be secured
Article 46 of the road traffic law requires a parked vehicle to be secured against being started by an unauthorised person and requires the driver to take other precautions necessary to prevent an accident.
The provision does not lay down one identical set of movements for all types of car.
In practice, how the vehicle is secured depends on its design.
It may include, among other things:
- correct use of the parking brake,
- putting the automatic gearbox in position
P, - in a manual car, leaving an appropriate gear engaged as additional security, if this is appropriate for the vehicle and the situation,
- switching off the drive in accordance with the vehicle's instructions,
- locking the car.
Good practice: learn the procedure recommended by the manufacturer of the particular car.
25. A hill changes how the car behaves
On a level surface, after the brake is released, the vehicle may stay where it is or start to move very slowly.
On a hill, there is additionally a component of gravity that makes the vehicle tend to roll downhill.
This is why a hill start requires coordination of:
- tractive force,
- the brake,
- in a manual car, also the clutch.
The aim is to go from standing still to driving forwards without rolling back uncontrollably.
26. Manual — a hill start using the parking brake
One of the most controlled techniques in a car with a manual gearbox is to use the parking brake.
The general pattern:
- stop the car and secure it with the parking brake,
- select first gear,
- prepare the drive — using the clutch and the accelerator pedal appropriately,
- feel for the moment when the car is ready to move forwards,
- release the parking brake,
- complete moving off smoothly.
What matters most is coordinating the moment of releasing the brake with the build-up of sufficient tractive force.
If the brake is released too early:
→ the vehicle may start to roll back.
If the clutch is released too abruptly or the engine speed is wrong:
→ the engine may stall or the car may jerk.
This describes driving technique, not a statutory instruction specifying the pedal positions in a particular car.
27. Hill start — the current Category B test criterion
In the state practical exam, moving off forwards on an uphill gradient is, for Category B, a task carried out in the manoeuvring area.
The current criterion requires that:
- the car does not roll back more than 0.2 m when moving off,
- the engine does not stall.
After stopping the vehicle on the hill, the candidate:
- applies or activates the parking brake,
- then moves off forwards while releasing it.
This is a specific test criterion.
The value of 0.2 m should not be presented as a general rule of the road traffic law stating how far a car “may roll back” during ordinary driving on the road.
In road traffic, the driver must above all keep control of the vehicle and not cause a hazard or obstruction.
28. Hill Hold, Auto Hold and the electric parking brake
Modern cars may be equipped with systems that make hill starts easier.
Hill Hold / Hill Start Assist
It may maintain pressure in the braking system for a short time after the brake pedal is released.
Auto Hold
It may hold the vehicle in place until you start to move off.
Electric parking brake
It may be applied with a button and, in some vehicles, released automatically when moving off.
The systems differ in how they work and how long they hold the brakes.
Do not assume that every car:
- has such a system,
- will behave in the same way,
- will hold the car for an unlimited time.
Exam
The current criterion for the uphill-gradient task expressly requires that, after stopping, the parking brake is applied or activated and the vehicle then moves off forwards while releasing it.
This is why the presence of a Hill Hold system should not be treated as a reason to skip the required exam procedure.
29. An automatic or electric car can also roll on a slope
Not having a clutch pedal does not mean that the driver does not have to control the vehicle on a hill.
Depending on the design and settings, the car may:
- stay stationary,
- creep forwards,
- start to roll,
- be held by the Auto Hold or Hill Hold system.
This is why, before releasing the brake, you need to know how the particular vehicle behaves.
In road traffic, you must not base safety on the assumption:
“the automatic will certainly hold me by itself”.
30. Moving off uphill on a slippery surface
Snow, ice or a loose surface reduce grip.
If the drive is applied too abruptly, wheelspin may occur.
Good technique involves:
- increasing the drive torque gently,
- avoiding abrupt movements of the accelerator pedal,
- maintaining the direction of travel,
- using the vehicle's systems as intended.
Depending on the car, the manufacturer may provide a special driving mode for snow or slippery surfaces.
There is no single universal gear or engine-speed technique that suits every vehicle and every surface.
31. Moving off downhill also requires control
On a downhill slope, the car may start to gain speed immediately after the brake is released.
This is why, when starting to drive downhill, you need to control:
- speed,
- direction,
- the space ahead of the vehicle,
- the movement of other road users.
Do not let the car roll uncontrollably just because “it moves by itself”.
We covered the principles of choosing the right gear and engine braking in M7.3.
32. Manoeuvring on a slope requires an extra margin
When parking on a slope, the difficulty lies in controlling at the same time:
- the vehicle's path,
- speed,
- the vehicle's tendency to roll.
This is why it is worth:
- making movements even more slowly,
- keeping a larger gap from obstacles,
- not allowing uncontrolled rolling,
- securing the car properly when you finish parking.
The law does not lay down one pedal technique for every type of drivetrain.
33. Do not carry out a manoeuvre “from memory” when the situation has changed
A pattern learned during practice works only when the conditions are similar.
In reality, the following change:
- the width of the space,
- the length of the neighbouring cars,
- the position of the lines,
- the angle of the parking space,
- the gradient of the surface,
- the presence of pedestrians,
- visibility conditions.
This is why every stage of the manoeuvre requires renewed observation.
If the real picture does not match the memorised pattern:
respond to reality, not to a memorised point.
34. What is a legal rule, what is a test requirement and what is technique?
Legal obligations
Among other things, the law specifies:
- the driver's obligations when reversing,
- the places where reversing is prohibited,
- the conditions for permitted stopping and parking,
- the obligation to use the method of parking indicated by signs,
- the obligation to secure the vehicle while parked.
Training and test requirements
For Category B, the official programme includes, among other things:
- driving forwards and in reverse,
- angled, perpendicular and parallel parking in road traffic,
- moving off forwards on an uphill gradient.
In the exam:
- one of the three specified parking variants is carried out in road traffic,
- one correction of the path is allowed when parking,
- the hill start has its own criteria, including a maximum roll-back of 0.2 m.
Good technique
Good practice includes, among other things:
- manoeuvring very slowly,
- frequently changing the direction in which you look,
- monitoring the front corner when reversing with the wheels turned,
- understanding the path of the rear wheels,
- stopping and reassessing the situation after losing confidence,
- using the clutch only to the extent needed to control movement,
- learning how the systems of the particular car work.
Good technique should not be presented as a legal rule if the Act or the regulations do not require that specific action.
35. A simple pattern for safe manoeuvring
You can use the following model:
assess the space → check the surroundings → move off very slowly → watch the whole vehicle → stop if in doubt → correct → secure the car
Assess the space
Is the manoeuvre legal and do you have enough room?
Check the surroundings
Are there pedestrians, cyclists or vehicles nearby?
Move off very slowly
Keep to a pace that lets you stop the car immediately.
Watch the whole vehicle
Not only the direction of travel, but also the opposite corner and the path of the rear wheels.
Stop if in doubt
Do not try to “rescue” a wrong path by accelerating.
Correct
Correct the position if it is safe and permitted.
Secure the car
When you finish parking, use the securing measures appropriate for the vehicle.
Common pitfalls
1. Low speed does not remove the need to observe your entire surroundings carefully.
2. During a turn, the rear wheels follow a path further inside than the front wheels.
3. When reversing with the wheels turned, the front of the car swings out in the opposite direction.
4. Cameras and sensors are aids, not a substitute for the required observation.
5. When reversing, you give way to other road users and take particular caution.
6. Parking that is technically correct may still be illegal if you have chosen a place where it is prohibited.
7. For Category B, exam parking takes place in road traffic, not as a separate parking task in the manoeuvring area.
8. In the Category B exam, perpendicular and angled parking are done entering forwards and exiting in reverse, and parallel parking entering in reverse and exiting forwards.
9. The current Category B parking criteria allow one correction of the vehicle's path.
10. There is no single universal “point in the mirror” that suits all cars.
11. Do not use contact with the kerb or another obstacle as a way of positioning the car.
12. A correction made deliberately and safely is better than continuing along the wrong path.
13. The hill start in the exam has a specific criterion: the vehicle must not roll back more than 0.2 m and the engine must not stall.
14. The value of 0.2 m is a test criterion, not a general statutory “permitted roll-back limit” in road traffic.
15. Hill Hold or Auto Hold does not remove the need to learn how the particular car behaves.
16. In the exam hill start, the current rule requires the parking brake to be activated.
17. In a manual car, prolonged driving with the clutch partly depressed increases clutch wear.
18. When you finish parking, the car must be secured properly.
Sources
- Rozporządzenie Ministra Infrastruktury i Budownictwa z dnia 4 marca 2016 r. w sprawie szkolenia osób ubiegających się o uprawnienia do kierowania pojazdami, instruktorów i wykładowców, consolidated text published in Dz.U. 2018 poz. 1885, as subsequently amended:
- Annex No. 1, part I,
officialTopic 2.9— “Vehicle control techniques”, - detailed practical programme: point 1.2 — moving off and driving forwards and in reverse along a traffic lane,
- point 1.6 — moving off forwards on an uphill gradient for Category B,
- points 2.11–2.13 — angled, perpendicular and parallel parking in road traffic for Categories B/B1.
- Annex No. 1, part I,
- Rozporządzenie Ministra Infrastruktury z dnia 11 października 2023 r., Dz.U. 2023 poz. 2317 — later amendment to the training regulations; no change was found to the elements of the practical programme used in this lesson.
- Rozporządzenie Ministra Infrastruktury z dnia 24 listopada 2023 r. w sprawie egzaminowania osób ubiegających się o uprawnienia do kierowania pojazdami, szkolenia, egzaminowania i uzyskiwania uprawnień przez egzaminatorów oraz wzorów dokumentów stosowanych w tych sprawach, Dz.U. 2023 poz. 2659, as subsequently amended:
- Annex No. 1, Table No. 1 and Table No. 3 — moving off and driving forwards and in reverse along a traffic lane, and moving off forwards on an uphill gradient,
- in the uphill-gradient task: the vehicle must not roll back more than 0.2 m, the engine must not stall, and after stopping the parking brake must be applied or activated and the vehicle moved off forwards while releasing it,
- Annex No. 1, Table No. 6, item 11 — for Category B, one of the parking manoeuvres in road traffic: perpendicular, entering forwards/exiting in reverse; angled, entering forwards/exiting in reverse; or parallel between two vehicles, entering in reverse/exiting forwards; the current criteria allow one correction of the vehicle's path.
- Rozporządzenie Ministra Infrastruktury z dnia 12 stycznia 2024 r., Dz.U. 2024 poz. 56, and rozporządzenie Ministra Infrastruktury z dnia 21 maja 2025 r., Dz.U. 2025 poz. 696 — later amendments to the examination regulations; no change was found to the indicated Category B parking or hill-start criteria.
- Ustawa z dnia 20 czerwca 1997 r. — Prawo o ruchu drogowym, consolidated text Dz.U. 2024 poz. 1251, as subsequently amended:
- Article 19(1)–(2) — control of the vehicle and safe braking,
- Article 23(1) point 3 and (2) — obligations and prohibitions concerning reversing,
- Article 46 — general conditions for stopping and parking and the obligation to secure the vehicle,
- Articles 47–49 — specific rules and prohibitions on stopping or parking; developed earlier in
M3.3.
- The state of the law on 22 August 2026 takes into account the later acts amending the road traffic law in force up to that date, including the Act of 23 January 2026, Dz.U. 2026 poz. 180. No change to Article 23 or Article 46 affecting the content of this lesson was found.
- Ustawa z dnia 17 lipca 2026 r., Dz.U. 2026 poz. 1073, was announced on 10 August 2026, but its amendments to the road traffic law enter into force in 2027; it does not affect the legal position of M7.5 as at 22 August 2026.
- Driving-technique note:
- a very low manoeuvring speed, monitoring the whole outline, allowing for the path of the rear wheels, watching the front swing out, stopping after losing confidence and using reference points only as an aid for a particular vehicle are principles of practical technique, not separate rules of the road traffic law,
- how the clutch, automatic gearbox, parking brake, Hill Hold, Auto Hold and regenerative braking work depends on the vehicle's design; the driver should know how to operate the particular car.
- State of the law checked in the official ELI on 22 August 2026.
