Smooth and energy-efficient driving
Contents
Energy-efficient driving is not about always driving as slowly as possible or avoiding the brake at all costs.
It is based on smoothness, anticipation and correct use of the vehicle's energy.
A driver who observes the situation early enough can limit the number of unnecessary accelerations and sudden braking manoeuvres, while keeping a larger safety margin.
This is why good energy-efficient driving is very often also driving that is:
- calmer,
- more predictable,
- less demanding on the car,
- easier for other road users to read.
From the outset, however, three things must be kept apart:
- the road traffic rules, which specify, among other things, the required safe speed, the way of braking and the distance,
- training and test requirements, which expressly cover energy-efficient gear changing and engine braking,
- good practice in economical driving, the details of which depend on the vehicle, the drive, the gearbox, the conditions and the traffic situation.
1. Safety takes precedence over saving
The most important principle is:
we do not do anything “to save energy” if it reduces safety.
Poland's Prawo o ruchu drogowym (the road traffic law) requires driving at a speed that ensures control of the vehicle, taking into account, among other things:
- the terrain,
- the condition and visibility of the road,
- the condition and load of the vehicle,
- weather conditions,
- traffic volume.
The driver is also obliged to:
- brake in a way that does not cause a hazard or obstruct traffic,
- keep the distance needed to avoid a collision if the vehicle in front brakes or stops.
This is why the following approach would be wrong:
“I won't brake, because I want to drive economically.”
If the situation requires braking — you brake.
Energy efficiency is mainly about avoiding situations in which earlier anticipation would have allowed you not to accelerate or brake unnecessarily.
2. Anticipation is the basis of smooth driving
The key to smooth driving is looking far enough ahead of the vehicle.
If the driver looks only at the car directly in front, they often react only when:
- the vehicle in front is already braking hard,
- the traffic lights are very close,
- the traffic lane is just ending,
- the bend turns out to be tighter than expected,
- a pedestrian appears at a crossing.
A driver who observes further ahead can notice a change in the situation earlier and, correspondingly earlier:
- lift off the accelerator,
- reduce speed,
- prepare the right gear,
- increase the distance,
- choose the right lane,
- avoid unnecessary acceleration.
Example
You can see a red light a few hundred metres ahead, and a queue of vehicles is already standing.
There is no point in accelerating hard only to brake heavily a moment later.
It is more sensible to:
- assess the situation earlier,
- stop increasing your speed unnecessarily,
- lose speed calmly,
- keep an appropriate distance,
- be ready to stop if the signal does not change.
Two cars heading for the same red lights:
- driver A accelerates and brakes hard,
- driver B eases off the accelerator earlier and arrives smoothly.
3. Smoothness does not mean driving without changes in speed
Road traffic requires constant adjustment of speed.
Smooth driving does not mean:
“keep exactly the same speed regardless of the situation”.
Rather, it means:
- changing speed early enough,
- avoiding unnecessarily abrupt changes,
- keeping an appropriate reserve of time and space,
- using information from the surroundings before a sudden reaction becomes necessary.
If ahead of you there is:
- a pedestrian crossing,
- an intersection,
- a tight bend,
- a queue of vehicles,
- restricted visibility,
- a dangerous road surface,
smooth driving technique may mean precisely reducing speed earlier.
4. Accelerate when acceleration makes sense
Not all acceleration is uneconomical.
The car must get up to a speed appropriate for the conditions and the traffic arrangements.
The problem is mainly acceleration that you will have to “give back” to the brakes a moment later.
Example
Ahead of you:
- a red light,
- a visible traffic jam,
- a car preparing to turn,
- a speed restriction starting a few dozen metres away.
Accelerating hard in such a situation usually brings no real benefit.
Good practice
Accelerate:
- smoothly,
- decisively enough to fit efficiently into the flow of traffic,
- without unnecessarily holding on to low gears,
- taking into account grip and the situation ahead of the vehicle.
We do not teach the rule:
“always accelerate as slowly as possible”.
Accelerating too slowly may obstruct traffic and is not necessarily the most efficient way of using a particular drive.
5. Keeping as steady a pace as possible
If conditions allow, it is better to keep a relatively stable speed than to go through a constant cycle of:
accelerator → brake → accelerator → brake
Every unnecessary increase in speed means giving the vehicle additional energy.
If it has to be shed by braking a moment later, part of that energy is irretrievably dissipated.
In a vehicle with regenerative braking, part of the energy may be recovered, but the recovery is never one hundred per cent.
This is why, even in an electric car, the basis of economical driving remains anticipation and limiting unnecessary changes in speed.
6. An appropriate distance also helps you drive more smoothly
Too short a distance from the vehicle in front means that the driver has to react to every small change in its speed.
The effect may look like this:
braking → acceleration → braking → acceleration
With a larger, safe distance it is easier to:
- notice a change in the pace of traffic earlier,
- adjust your speed gently,
- avoid unnecessary braking,
- keep a better field of observation.
However, we do not increase the distance “for the environment” according to a single arbitrary number.
The distance must above all meet the safety requirements covered in Module 6.
7. Lifting off the accelerator earlier instead of braking late
If you know that you will soon need to reduce speed, you can often earlier:
- reduce pressure on the accelerator pedal,
- release it completely,
- use driving resistance,
- use engine braking,
- in a hybrid or EV, use the regenerative braking provided by the car.
This does not mean that you may slow down too early in a way that obstructs traffic.
Your speed must be:
- safe,
- in line with the limits,
- suited to the situation,
- not obstructing other drivers without reason.
8. Engine braking is part of the official programme
The official practical training programme lists:
using engine torque while braking — engine braking.
In the state practical exam for Category B, too, this is a separately assessed element of the drive.
Engine braking allows you to reduce speed without immediately disengaging the drive.
It can be useful, among other things:
- before a foreseeable speed restriction,
- before a bend,
- when approaching an intersection,
- during a longer descent.
We covered it in detail in M7.3.
Important
Engine braking does not replace the service brake when faster or decisive speed reduction is needed.
9. Do not select neutral just to “save”
Coasting in neutral is not a universal method of energy-efficient driving.
In such a situation, the driver loses the natural slowing effect of the drivetrain and may need to use the brake more often.
In many modern cars, fuel consumption while driving in gear with the accelerator pedal released is managed electronically by the vehicle.
So do not apply the old simplification:
“neutral always means the lowest consumption”.
Good practice is to stay in an appropriate gear and keep control of the drive, unless the particular vehicle design itself provides a coasting function in accordance with its own control system.
This is a technical recommendation, not a separate rule of the road traffic law specifying one mandatory way of using the gearbox in every situation.
10. Gear changing and energy-efficient driving
The official practical training programme expressly lists:
gear changing appropriate for energy-efficient driving.
In the state exam for Category B, a specific criterion has been adopted:
- changing up at an engine speed of 1800–2600 rpm,
- the first four gears should be engaged before reaching 50 km/h.
This is a test criterion, not a general table for every drive
Do not draw the conclusion from it that:
“at every speed a specific gear must always be engaged”.
In real traffic, the right gear also depends on:
- the vehicle's load,
- the gradient of the road,
- the need to accelerate,
- the engine characteristics,
- grip,
- the traffic situation.
If you need an adequate reserve of tractive force, e.g. on an ascent, do not select too high a gear just to lower the engine speed.
11. A gear that is too low or too high may reduce smoothness
Gear too low
This may cause:
- unnecessarily high revs,
- louder engine running,
- greater sensitivity to movements of the accelerator pedal,
- less smooth driving.
Gear too high
This may cause:
- revs that are too low,
- a weak response of the car to the accelerator,
- uneven or labouring engine running,
- the need to press the accelerator hard or to change down later.
The aim, therefore, is not:
“the highest possible gear at all costs”, but the gear appropriate to the situation and to how the particular engine runs.
12. Do not hold on to low gears unnecessarily
If the car has reached a speed at which it can run efficiently in a higher gear, further driving in a low gear at high revs is usually not needed.
In normal, calm driving, it is therefore worth:
- accelerating the vehicle smoothly,
- changing gear without unnecessarily high revs,
- once the appropriate speed is reached, keeping a gear that lets the engine run efficiently.
An exception may be a situation in which safety or the dynamics of the traffic require you to stay in a lower gear, e.g. before an ascent or when decisive acceleration is necessary.
13. Smooth driving in a traffic jam
In slow traffic, a common mistake is constant:
- moving off,
- accelerating for a few metres,
- braking,
- moving off again.
If the situation allows, it is worth leaving a gap that lets you “smooth out” some of the small changes in the speed of the vehicle in front.
This may reduce the number of abrupt starts and stops.
But do not create an unjustifiably large gap
The driver should still:
- behave predictably in traffic,
- not obstruct others without need,
- take into account other vehicles changing lanes,
- stay ready to stop.
14. Watch the whole line of traffic, not just one car
If, through the windows of the vehicles in front, you can see brake lights coming on a few cars ahead, you can prepare earlier to reduce speed.
If you can see that:
- the traffic lights have changed to red,
- a queue is forming before a crossing,
- a lorry is starting up an ascent,
- the traffic lane is narrowing,
you do not have to wait until the car directly in front of you makes a sudden movement.
This is one of the most important differences between a driver who reacts late and a driver who drives with anticipation.
15. Ascent — use your momentum, but do not break safety rules
Before an ascent, you can prepare early enough:
- the right speed,
- the appropriate gear,
- a reserve of tractive force.
This helps you avoid a situation in which the car suddenly loses speed on the ascent and the driver changes down late.
However, this does not mean permission to accelerate the car above the permitted or safe speed before the ascent.
The vehicle's kinetic energy can help it climb the ascent, but the limits are set by the legal rules and by safety.
16. Descent — do not coast in neutral and do not spare the brakes at the expense of control
On a longer descent, correct technique includes:
- selecting an appropriate gear,
- using engine braking or a drivetrain braking function,
- using the service brake when it is needed,
- keeping a speed appropriate to the bends, the gradient and the grip.
Do not drive downhill in neutral just because the car “rolls by itself”.
Particularly on a long descent, keeping full control of your speed is more important than a momentary saving.
17. Driving through a bend — prepare your speed before the bend
Energy-efficient and smooth technique is not about braking hard in the middle of a bend and then accelerating sharply out of it, if the right speed could have been chosen earlier.
A good sequence in normal conditions is:
observation → choosing the speed before the bend → smooth driving through → calm acceleration on the way out
Road conditions may of course require additional braking in the bend itself.
Safety always takes precedence over perfect smoothness.
18. Traffic lights — do not “hunt” for the green at all costs
Seeing a green signal in the distance does not mean that you should accelerate sharply to make it at all costs.
The signal may change before you reach the intersection.
Likewise, a red light does not mean that you must brake very hard straight away if there is still a large safe distance to the intersection and you can lose speed calmly.
The driver should:
- observe the traffic lights,
- assess the situation,
- stay ready to stop,
- not exceed the permitted speed,
- not enter on yellow if they can stop without sudden braking.
19. Cruise control can help, but it does not replace the driver
On a suitable road, cruise control can make it easier to keep a relatively constant speed.
However, this does not mean that it should always be used.
The driver must take into account:
- traffic volume,
- grip,
- bends,
- ascents and descents,
- weather conditions,
- the capabilities of the particular system.
In difficult conditions, keeping a constant speed by automation may not be the best solution.
Adaptive cruise control
ACC can reduce and increase speed by itself, keeping a programmed distance.
Nevertheless, it still:
- does not relieve the driver of the need to observe the road,
- has technical limitations,
- may respond differently from an experienced driver who anticipates the situation far ahead of the vehicle.
20. Automatic gearbox
In a car with an automatic gearbox, the driver does not make every gear change manually, but still has a great influence on smoothness through the way they use the accelerator pedal and the brake.
Pressing the accelerator pedal abruptly may cause:
- a downchange,
- a rise in engine speed,
- stronger acceleration.
Smooth accelerator inputs allow the gearbox to operate more smoothly, if conditions allow.
Some cars have the following modes:
- Eco,
- Normal,
- Sport,
- manual gear selection.
We do not teach the rule:
“Eco mode is always the safest and should be used in every situation”.
The driving mode is a tool. The driver is responsible for adapting the vehicle's behaviour to the situation.
21. Hybrids and electric cars — regenerative braking
In hybrids and electric cars, reducing pressure on the accelerator pedal may cause regenerative braking.
The electric motor then acts as a generator, and part of the energy of motion is converted back into electrical energy.
The strength of regenerative braking depends on:
- the vehicle's design,
- the selected driving mode,
- the battery's state of charge,
- temperature,
- the current limitations of the system.
Regenerative braking does not mean “free braking”
Energy recovery is never complete.
The most efficient approach is still not to build up unnecessary excess speed that you will have to get rid of a moment later.
One-pedal driving
Some EVs allow a style of driving in which a large part of the slowing down takes place after you lift off the accelerator pedal.
The driver must learn how the particular car behaves.
When faster braking is needed, they still use the service brake.
22. Air conditioning and electrical consumers
Running the air conditioning, window heating, interior heating and other electrical consumers requires energy.
However, do not switch off equipment needed to:
- ensure visibility,
- demist the windows,
- maintain a level of comfort that allows you to drive safely.
Example
If the windows are misting up, the priority is to clear them effectively.
Do not switch off ventilation or air conditioning just to reduce energy consumption.
23. The condition of the vehicle affects energy consumption
Driving resistance and energy consumption are also affected by technical factors, e.g.:
- incorrect tyre pressure,
- unnecessary weight,
- additional items that increase aerodynamic drag,
- vehicle faults.
This does not mean that the driver has to calculate the effect of every element on fuel consumption every day.
However, they should keep the vehicle in proper condition and use the values specified by the manufacturer.
The vehicle's technical condition is covered in Module 12.
24. An engine running while parked — here there is a specific legal prohibition
You must distinguish an economy recommendation from a legal rule.
The road traffic law prohibits the driver from leaving the engine running while parked in a built-up area.
The exception concerns a vehicle carrying out work on the road.
This is a legal obligation, not just advice about saving fuel.
An important distinction
The provision refers to parking.
This does not mean an obligation to switch off the engine at every short stop resulting, e.g., from:
- a red signal,
- a traffic jam,
- giving way.
Such a standstill may be a stop resulting from traffic conditions or traffic rules, not parking within the meaning of the Act.
In cars fitted with a Start-Stop system, the electronics may switch the engine off and restart it by themselves in accordance with the system's operating conditions.
25. Start-Stop — an assistance system, not a driving obligation
An automatic Start-Stop system may switch off the engine while parked or during a short stop and restart it when the car is to move off.
How it works depends on the car.
The system may not operate, e.g., because of:
- engine temperature,
- the battery's condition,
- air-conditioning demand,
- other conditions specified by the manufacturer.
If Start-Stop does not operate, do not automatically assume that the system is faulty or that the driver is breaking the rules.
26. Energy-efficient driving does not mean obstructing traffic
Examples of incorrect “saving” include:
- very slow acceleration of the car on a road where this obstructs traffic,
- driving much more slowly than conditions require solely to reduce consumption,
- creating very large gaps in flowing traffic,
- not carrying out the necessary acceleration when joining faster traffic.
Article 19 requires not only keeping a speed that ensures control of the vehicle, but also driving at a speed that does not obstruct other drivers.
Economical technique should be part of efficient driving, not its opposite.
27. Do not save at the expense of safety when overtaking
If carrying out the manoeuvre legally and safely requires adequate acceleration, the driver should use the vehicle's capabilities as needed to complete the manoeuvre efficiently.
Do not:
- select too high a gear just for low revs,
- prolong overtaking for fear of higher momentary fuel consumption,
- give up a necessary downchange.
The first thing to ensure is that the manoeuvre is carried out safely.
The detailed rules on overtaking were covered in Module 3.
28. “Eco-driving” is not one magic set of engine speeds
Different cars have different:
- engines,
- gear ratios,
- mass,
- torque characteristics,
- hybrid systems,
- automatic gearbox strategies,
- regenerative braking systems.
This is why, apart from the specific test criteria, you should not teach one universal table:
speed X → always gear Y → always engine speed Z
In practice you need to:
- know the basic principles,
- listen to and observe how the vehicle works,
- follow the manufacturer's recommendations,
- adapt your technique to the traffic situation.
29. What exactly is required in the Category B exam?
The current examination regulations specify two separate elements related to energy-efficient driving.
1. Gear changing appropriate for energy-efficient driving
For Category B:
- changing up should take place at 1800–2600 rpm,
- the first four gears should be engaged before reaching 50 km/h.
2. Using engine torque while braking
The candidate should use engine braking.
What about a car without a manual gearbox?
The range of actions carried out by the driver depends on the design of the driving-test vehicle.
In a car in which gear changes are made automatically, the driver does not manually carry out the same sequence as in a manual.
This does not change the general idea of smooth driving: observe early enough, avoid unnecessary changes of pace and use the characteristics of the drive.
30. Smooth driving can increase the safety margin
Smoothness matters not only because of fuel or energy.
A driver who anticipates well:
- notices hazards earlier,
- is less often forced to brake suddenly,
- keeps their distance more easily,
- has more time to decide,
- is less likely to surprise passengers and other road users.
This does not mean that a smooth driver never brakes in an emergency.
If a hazard suddenly appears, you must react as decisively as the situation requires.
31. A simple model of smooth and energy-efficient driving
You can remember the sequence:
look far ahead → anticipate → keep your distance → accelerate only when it makes sense → ease off earlier → choose the right gear → brake smoothly → react decisively when safety requires it
Look far ahead
Do not focus your eyes only on the car in front of you.
Anticipate
Assess the lights, intersections, bends, queues and the behaviour of others.
Keep your distance
Leave yourself space for a calm change of speed.
Accelerate when it makes sense
Do not speed the car up if you will have to brake soon anyway.
Ease off earlier
Let the car lose speed gradually if the situation is predictable.
Choose the right gear
Do not hold on to a low gear unnecessarily or “labour” the engine in too high a gear.
Brake smoothly
If you have time and space, reduce speed gradually.
React decisively
When a real hazard appears, safety takes precedence over smoothness and saving.
Common pitfalls
1. Energy-efficient driving does not mean driving as slowly as possible.
2. Safety always takes precedence over saving fuel or energy.
3. The main basis of smoothness is anticipating situations, not just “pressing the accelerator gently”.
4. Do not accelerate hard towards a place where you already know you will have to slow down.
5. An appropriate distance helps limit constant braking and accelerating.
6. Engine braking is part of the official training programme and the exam.
7. Coasting in neutral is not a universal method of saving fuel.
8. The criterion of 1800–2600 rpm and the first four gears before 50 km/h is a test criterion for Categories B/B+E, not a general rule of the road traffic law specifying the gear for every speed.
9. A gear that is too high may worsen the vehicle's response and how the engine runs.
10. Before an ascent, do not accelerate the car above the permitted or safe speed just to “build up energy”.
11. On a descent, do not drive in neutral just to let the car roll more freely.
12. Regenerative braking recovers part of the energy, but it does not eliminate the losses caused by unnecessary acceleration and braking.
13. We do not switch off the air conditioning or heating at the expense of visibility and safe driving conditions.
14. Cruise control and ACC are aids, not a substitute for observation and adapting your speed to the conditions.
15. Leaving the engine running while parked in a built-up area is, as a general rule, prohibited — this is a legal rule, not just economy advice.
16. Not every stop in traffic is “parking”. A red light or a traffic jam does not automatically mean an obligation to switch off the engine.
17. Eco mode does not remove the driver's responsibility to make safe decisions.
18. When overtaking, do not prolong the manoeuvre just to keep the revs low.
19. Smooth driving does not rule out hard braking if a sudden hazard appears.
20. There is no single universal recipe for eco-driving that suits all combustion-engine, hybrid and electric cars.
Sources
- Rozporządzenie Ministra Infrastruktury i Budownictwa z dnia 4 marca 2016 r. w sprawie szkolenia osób ubiegających się o uprawnienia do kierowania pojazdami, instruktorów i wykładowców, consolidated text published in Dz.U. 2018 poz. 1885, as subsequently amended:
- Annex No. 1, part I,
officialTopic 2.9— “Vehicle control techniques”, - Annex No. 1, part II, point 2.27 — “Gear changing appropriate for energy-efficient driving”,
- point 2.28 — “Using engine torque while braking — engine braking”.
- Annex No. 1, part I,
- Rozporządzenie Ministra Infrastruktury z dnia 11 października 2023 r., Dz.U. 2023 poz. 2317 — later amendment to the training regulations; no change was found to points 2.27–2.28 indicated above.
- Rozporządzenie Ministra Infrastruktury z dnia 24 listopada 2023 r. w sprawie egzaminowania osób ubiegających się o uprawnienia do kierowania pojazdami, szkolenia, egzaminowania i uzyskiwania uprawnień przez egzaminatorów oraz wzorów dokumentów stosowanych w tych sprawach, Dz.U. 2023 poz. 2659, as subsequently amended:
- Annex No. 1, table concerning tasks carried out in road traffic,
- item 26 — gear changing appropriate for energy-efficient driving; for Categories B and B+E, changing up at 1800–2600 rpm and engaging the first four gears before reaching 50 km/h,
- item 27 — using engine torque while braking — engine braking.
- Rozporządzenie Ministra Infrastruktury z dnia 12 stycznia 2024 r., Dz.U. 2024 poz. 56, and rozporządzenie Ministra Infrastruktury z dnia 21 maja 2025 r., Dz.U. 2025 poz. 696 — two acts amending the examination regulations listed in ELI; no change was found to items 26–27 used in this lesson.
- Ustawa z dnia 20 czerwca 1997 r. — Prawo o ruchu drogowym, consolidated text Dz.U. 2024 poz. 1251, as subsequently amended:
- Article 19(1) — speed that ensures control of the vehicle, taking traffic conditions into account,
- Article 19(2) — the obligation to drive at a speed that does not obstruct other drivers, to brake safely and to keep the necessary distance,
- Article 60(2) point 3 — prohibition on leaving the engine running while parked in a built-up area, except for a vehicle carrying out work on the road.
- The state of the law on 22 August 2026 takes into account the later amendments to the road traffic law in force up to that date, including the 2025 amendments and the Act of 23 January 2026, Dz.U. 2026 poz. 180. No change to Article 19 or Article 60(2) point 3 affecting the content of M7.6 was found.
- Ustawa z dnia 4 grudnia 2025 r., Dz.U. 2025 poz. 1872, added Article 60(5) from 30 March 2026, concerning deliberately causing the wheels to skid and causing a wheel to lose contact with the road surface; this amendment does not change Article 60(2) point 3 used here.
- Ustawa z dnia 17 lipca 2026 r., Dz.U. 2026 poz. 1073, was announced on 10 August 2026, but it enters into force on 11 May 2027; it does not affect the legal position of this lesson as at 22 August 2026.
- Driving-technique note:
- anticipating situations, avoiding unnecessary acceleration, smooth control, an appropriate distance, using driving resistance, an appropriate choice of gear, and the way cruise control, the automatic gearbox, Eco modes, Start-Stop and regenerative braking are used are driving-technique principles that depend on the situation and the vehicle's design; they are not separate universal rules of the road traffic law,
- how the automatic gearbox, regenerative braking, one-pedal driving, Start-Stop, cruise control and assistance systems work should be assessed in accordance with the instructions for the particular vehicle.
- State of the law checked in the official ELI on 22 August 2026.
