Category BM11.4
Lesson 4 of 5

Loads protruding beyond the vehicle's outline

Contents

Sometimes an item being carried is longer or wider than the car's load space. The mere fact that a load protrudes beyond the vehicle outline does not always mean that carrying it is prohibited, but the regulations set precise limits and marking requirements.

This is a topic where the figures matter.

Load protruding to the sides

A load may protrude beyond the side planes of the vehicle outline only if the total width of the vehicle with the load does not exceed:

  • 2.55 m — as a rule,
  • 3 m, if the vehicle itself is 2.55 m wide,

although in the second case the load must not protrude by more than 23 cm on one side.

For a typical passenger car, the most important rule is that after adding the protruding load you must still stay within the statutory limit for total width.

Load protruding at the rear

As a rule, a load must not protrude at the rear of a vehicle or combination of vehicles by more than:

2 m from the rear plane of the vehicle outline.

For a stake trailer, the regulations provide for a separate method of measurement, and for carrying long timber there is a special exception of up to 5 m. However, this is not a typical situation for a Category B passenger car.

Load protruding at the front

A load must not protrude at the front of the vehicle beyond either of these limits:

  • 0.5 m from the front plane of the vehicle outline, and
  • 1.5 m from the driver's seat.

Both conditions must be met.

Maximum height

The height of the vehicle together with the load must not exceed:

4 m.

This is particularly important when carrying items on the roof.

Before driving:

  • into a garage,
  • under a viaduct,
  • under a gate,
  • into an underground car park,

the driver should know the actual height of the car with a roof box, bikes or other load fitted.

When must a protruding load be marked?

Marking is required for:

  • a load protruding at the front of the vehicle,
  • a load protruding at the side of the vehicle,
  • a load protruding at the rear by more than 0.5 m.

So do not confuse two different values:

  • a maximum of 2 m of protrusion at the rear,
  • the obligation to mark the load once it protrudes at the rear by more than 0.5 m.

Marking a load protruding at the rear of a passenger car

For a passenger car or a trailer towed by a passenger car, the regulations allow a simple method of marking a load protruding at the rear:

a red flag measuring at least 50 × 50 cm, placed at the outermost edge of the load.

The regulations also provide for a general method of marking a load protruding at the rear using white and red stripes. In this general method, in conditions of insufficient visibility, a red light and a red retroreflector are also used on the rearmost edge of the load.

For a passenger car and a trailer towed by a passenger car, a red flag of at least 50 × 50 cm is a separate permitted alternative provided for in Article 61(9) point 4.

Marking a load protruding at the front

It is marked with:

  • an orange flag, or
  • two white and two red stripes visible from the sides and the front.

In conditions of insufficient visibility, a white light is also used on the foremost part of the load.

Load protruding at the side

It is marked with an orange flag measuring at least:

50 × 50 cm

at the outermost edge.

In conditions of insufficient visibility, the regulations require additional lights and reflective elements facing the front and the rear respectively.

Insufficient visibility changes the requirements

A flag that is visible in daylight may not be enough after dark or in conditions of reduced air transparency.

In such conditions, the regulations provide for additional lights and reflective elements for the protruding parts of the load.

That is why, when planning to transport a long item, you need to take into account not only the moment you set off, but also the conditions that may arise during the whole journey.

A protruding load must still meet all the other requirements

Staying within the dimension limits does not release you from the obligation of:

  • securing the load properly,
  • maintaining vehicle stability,
  • not obscuring the lights and plates,
  • not restricting visibility,
  • not exceeding the MAM and the payload.

A load that is correctly marked but badly secured is still being carried incorrectly.

Common pitfalls

1. “At the rear, a load may protrude by 2 m without any marking.” — NO. Once the load protrudes by more than 0.5 m, the obligation to mark it applies.

2. “The red flag can be any size.” — NO. In the variant for a passenger car, it must be at least 50 × 50 cm.

3. “The 4 m maximum height applies to the car itself, without the roof box.” — NO. What counts is the vehicle together with the load.

4. “If the load protrudes at the front only a little, it doesn't need to be marked.” — the regulations require a load protruding beyond the front plane of the vehicle outline to be marked.

5. “Marking replaces securing.” — NO.

Remember

REAR: MAX. 2 m — MARKING WHEN IT PROTRUDES >0.5 m. FRONT: MAX. 0.5 m FROM THE OUTLINE AND 1.5 m FROM THE DRIVER'S SEAT. HEIGHT OF THE VEHICLE WITH THE LOAD: MAX. 4 m.

Sources
  • Ustawa z dnia 20 czerwca 1997 r. — Prawo o ruchu drogowym:
    • Article 61(6) — permissible protrusion of the load beyond the vehicle outline,
    • Article 61(7) — the exception for long timber,
    • Article 61(8) — when a protruding load must be marked,
    • Article 61(9) points 1–4 — methods of marking a load protruding at the front, at the side and at the rear, including the red flag for a passenger car and a trailer towed by a passenger car,
    • Article 61(10) — the maximum height of the vehicle with the load.
  • Rozporządzenie Ministra Infrastruktury i Budownictwa z dnia 4 marca 2016 r. w sprawie szkolenia osób ubiegających się o uprawnienia do kierowania pojazdami, instruktorów i wykładowców — Annex No. 1, officialTopic 4.1: “Safety factors relating to the vehicle, load and persons carried; responsibility of the driver/vehicle keeper”.
↑